1. Introduction
This manual provides instructions for the assembly, operation, and maintenance of the Nexel Hanger Rail for Wire Shelving. The Nexel Hanger Rail is a 36-inch chrome-finished accessory designed to be mounted along the length or width of a wire shelving unit. It allows for easy attachment of hooks to hang various items, enhancing the storage capabilities of your shelving system. It is compatible with all Nexel Posts for Wire Shelving.
2. Safety Information
WARNING:
- Do not use this product in wet environments.
- Always follow assembly instructions carefully to ensure proper installation.
- Ensure proper installation and do not overload the hanger rail or the shelving unit.
- Always use the product as intended to prevent injury or damage.
3. Components
The Nexel Hanger Rail package typically includes the following components:
- One (1) Nexel Hanger Rail (36" L, Chrome Finish)
- Mounting clips or sleeves (may be pre-attached or separate, depending on design)
Figure 3.1: Nexel Hanger Rail shown installed between two shelving posts. This image illustrates the primary component of the product.
Figure 3.2: A top-down view of the Nexel Hanger Rail, highlighting its chrome finish and design for attaching hooks.
4. Setup and Assembly
Assembly of the Nexel Hanger Rail is designed to be straightforward. It requires attachment to existing Nexel wire shelving posts.
4.1 Tools Required
- No special tools are typically required for assembly.
4.2 Assembly Steps
- Prepare Shelving Unit: Ensure your Nexel wire shelving unit is fully assembled and stable. Identify the desired location for the hanger rail, either along the length or width of the unit.
- Attach Sleeves (if separate): If your hanger rail comes with separate plastic sleeves, snap them around the shelving posts at the desired height. Ensure they are securely seated in the grooves of the posts.
- Mount Hanger Rail: Slide the ends of the hanger rail over the plastic sleeves or directly onto the posts if the clips are integrated. Apply gentle downward pressure until the rail locks into place. The design allows for easy attachment to Nexel posts.
- Verify Stability: Once attached, gently tug on the hanger rail to ensure it is securely fastened and does not wobble.
Figure 4.1: Detail of the hanger rail's connection point to a shelving post, illustrating how it integrates with the wire shelving system.
5. Operating Instructions
The Nexel Hanger Rail is designed for simple operation once installed.
5.1 Attaching Items
- Use S-hooks, hangers, or other compatible hanging accessories to attach items to the hanger rail.
- Distribute weight evenly along the rail to maintain stability and prevent stress on the shelving unit.
- Do not exceed the weight capacity of the hanger rail or the overall shelving unit. Refer to your shelving unit's manual for specific weight limits.
5.2 Recommended Uses
This hanger rail is recommended for hanging items on wire shelving in various environments, including:
- Closets for clothing or accessories.
- Garages or utility rooms for tools or cleaning supplies.
- Kitchens for pots, pans, or utensils.
- Retail displays for merchandise.
6. Maintenance
To ensure the longevity and appearance of your Nexel Hanger Rail, follow these simple maintenance guidelines:
- Cleaning: Wipe the hanger rail with a dry cloth regularly to remove dust and dirt. For stubborn marks, a slightly damp cloth can be used, followed immediately by a dry cloth to prevent water spots.
- Avoid Abrasives: Do not use abrasive cleaners, scouring pads, or harsh chemicals, as these can damage the chrome finish.
- Environment: As stated in the safety information, avoid using the product in wet environments to prevent corrosion and maintain the chrome finish.
7. Troubleshooting
This section addresses common issues you might encounter with the Nexel Hanger Rail.
| Problem | Possible Cause | Solution |
|---|---|---|
| Hanger rail is loose or wobbly. | Improper installation; clips not fully engaged. | Ensure the hanger rail ends are fully seated onto the plastic sleeves or directly onto the shelving posts. Apply firm, even pressure until it clicks into place. |
| Difficulty attaching the rail. | Misalignment with posts; sleeves not correctly positioned. | Verify that the plastic sleeves (if applicable) are correctly snapped into the grooves of the shelving posts at the desired height. Align the rail ends precisely with the sleeves/posts. |
| Rail appears bent or damaged upon arrival. | Shipping damage. | Inspect the product immediately upon receipt. If significantly bent or damaged, contact Nexel customer support or your retailer for assistance. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | AHR36C |
| Product Dimensions | 2"D x 37"W x 1.5"H (approx. 2 x 37 x 1.5 inches) |
| Weight | 1.5 Pounds |
| Finish Type | Chrome |
| Material | Chrome over nickel electro plating |
| Assembly Required | Yes |
| Manufacturer | Nexel |
| Recommended Use | Hanging items on wire shelving in various environments |
9. Warranty and Support
Specific warranty information for the Nexel Hanger Rail is not provided in this manual. Please refer to the product packaging or the official Nexel website for detailed warranty terms and conditions.
For customer support, technical assistance, or to inquire about replacement parts, please contact Nexel directly through their official website or the retailer from whom you purchased the product.
Visit the official Nexel Store: Nexel Store on Amazon
