1. Introduction
This manual provides instructions for the safe installation, operation, and maintenance of your Hampton Bay Black Outdoor LED Wall Lantern. Please read this manual thoroughly before installation and keep it for future reference. This fixture is designed for outdoor use and features an integrated LED light source.
2. Safety Information
WARNING: RISK OF ELECTRIC SHOCK.
- Always turn off power at the circuit breaker or fuse box before installing, servicing, or cleaning this product.
- Consult a qualified electrician if you are unsure about the installation process.
- Ensure all electrical connections comply with local codes and ordinances, as well as the National Electrical Code (NEC).
- Do not install this fixture on surfaces that are easily flammable.
- This product is suitable for wet locations. Ensure all gaskets and seals are properly seated during installation to maintain water resistance.
- Do not attempt to modify the integrated LED light source. It is not user-replaceable.
CAUTION: RISK OF INJURY.
- Wear safety glasses and gloves during installation.
- Handle the fixture with care to avoid damage.
3. Package Contents
Verify that all parts listed below are included in your package:
- Outdoor LED Wall Lantern (1)
- Mounting Hardware Kit (screws, wire nuts, mounting plate) (1 set)
- Instruction Manual (this document) (1)
4. Setup and Installation
Before beginning installation, ensure the power is turned off at the circuit breaker.
Figure 1: Hampton Bay Black Outdoor LED Wall Lantern. This image shows the oval-shaped outdoor LED wall lantern with a black finish and a protective cage over a frosted diffuser. The light is illuminated, showing a warm glow.
- Prepare Wiring: Turn off power at the main fuse box or circuit breaker. Remove the old fixture if applicable.
- Attach Mounting Plate: Secure the mounting plate to the junction box using the provided screws. Ensure the plate is level and firmly attached.
- Make Electrical Connections:
- Connect the black wire from the fixture to the black (hot) wire from the junction box using a wire nut.
- Connect the white wire from the fixture to the white (neutral) wire from the junction box using a wire nut.
- Connect the ground wire from the fixture to the ground wire from the junction box (or to the green ground screw on the mounting plate) using a wire nut.
Ensure all wire nuts are securely tightened.
- Mount the Fixture: Carefully align the fixture with the mounting plate and secure it using the provided screws. Ensure the fixture is flush against the mounting surface and all seals are properly seated to prevent water intrusion.
- Restore Power: Turn the power back on at the circuit breaker. Test the light fixture to ensure it functions correctly.
5. Operating Instructions
This Hampton Bay LED Wall Lantern operates like a standard outdoor light fixture. Once properly installed and wired to a switch, simply toggle the wall switch to turn the light on or off.
- Power On/Off: Use the connected wall switch to control the light.
- Integrated LED: The fixture uses an integrated LED light source, which does not require bulb replacement.
6. Maintenance
Your LED wall lantern requires minimal maintenance.
- Cleaning: To clean the fixture, ensure the power is off. Wipe the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or electrical components.
- LED Care: The integrated LED is designed for long-term use and does not require bulb replacement. Do not attempt to open the sealed LED compartment.
- Inspection: Periodically inspect the fixture for any signs of damage or wear, especially to the wiring and seals.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. |
|
|
| Light flickers. |
|
|
| Water inside the fixture. |
|
|
If you experience issues not listed here or if the suggested solutions do not resolve the problem, please contact customer support.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Hampton Bay |
| Model Name | hampton bay |
| Part Number | HB8822LED-05 |
| UPC | 046335981164 |
| Light Source Type | Light Emitting Diode (LED) |
| Color | Black |
| Material | Alloy Steel, Aluminum |
| Finish Type | satin |
| Brightness | 1000 lumen |
| Wattage | 10 watts |
| Voltage | 120 Volts |
| Mounting Type | Wall Mount |
| Water Resistance Level | Waterproof |
| Specification Met | Energy Star |
| Item Weight | 2 Pounds |
| Item Dimensions (LxWxH) | 11.5 x 24 x 18 inches |
| Country of Origin | China |
9. Warranty and Support
Hampton Bay products are manufactured to high-quality standards. For specific warranty details, please refer to the warranty card included with your purchase or visit the official Hampton Bay website. For technical support, replacement parts, or general inquiries, please contact Hampton Bay customer service. Contact information can typically be found on the product packaging or the brand's official website.
Please retain your proof of purchase for warranty claims.
