Bromic Heating BH0420032

Download PDF
Contents

Bromic Tungsten Smart Heat 4000W Electric Patio Heater Instruction Manual

Model: BH0420032

1. Introduction

This manual provides essential information for the safe and efficient operation of your Bromic Tungsten Smart Heat 4000W Electric Patio Heater. Please read these instructions thoroughly before installation and use, and retain them for future reference. This heater is designed for outdoor use, providing radiant heat for commercial and residential environments.

2. Important Safety Information

WARNING: Failure to follow these instructions may result in electric shock, fire, property damage, or injury.

  • Electrical Requirements: This heater requires a 220V-240V electrical supply with an approximate amperage of 16.6A. Installation must be performed by a qualified electrician in accordance with all local electrical codes. Ensure the electrical circuit is adequately rated for the heater's power consumption.
  • Placement: Maintain minimum clearances from combustible materials. For wall mounting, a minimum clearance of 72 inches (183 cm) is required. For ceiling mounting, a minimum clearance of 96 inches (244 cm) is required. Do not install near flammable liquids, gases, or other combustible materials.
  • Water Exposure: The heater has an IPX4 water ingress rating, indicating it is protected against splashing water from any direction. However, avoid direct high-pressure water jets.
  • Proposition 65 Warning: This product may expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.
  • Supervision: Do not leave the heater unattended while operating. Keep children and pets away from the heater.
  • Maintenance: Disconnect power before performing any maintenance or cleaning.
  • Damage: Do not operate the heater with a damaged cord or plug, or if the heater malfunctions or has been dropped or damaged in any manner.

3. Product Overview

The Bromic Tungsten Smart Heat 4000W Electric Patio Heater is a dual-element infrared heater designed for efficient outdoor heating. It features a black high-temperature ceramic coating for durability and a sleek aesthetic. The spectral reflector enhances heat output from the frosted infrared tube elements, minimizing light emission and glare.

Bromic Tungsten Smart Heat 4000W Electric Patio Heater, front view

Figure 1: Front view of the Bromic Tungsten Smart Heat 4000W Electric Patio Heater, showcasing its black finish and protective grille.

Bromic Tungsten Smart Heat 4000W Electric Patio Heater, angled view

Figure 2: Angled view of the Bromic Tungsten Smart Heat 4000W Electric Patio Heater, highlighting its compact design and heating elements.

Key Features:

  • Dual Quartz Heating Elements: Delivers rapid and consistent infrared heat.
  • Durable Construction: Premium stainless steel with a high-temperature, corrosion-resistant black finish.
  • Adjustable Mounting: Includes brackets for wall or ceiling installation with adjustable angles.
  • Energy Efficient: Infrared technology focuses heat on objects and people, reducing energy waste.
  • Weatherproof: IPX4 water ingress rating for outdoor reliability.

4. Setup & Installation

Proper installation is critical for the safe and effective operation of your heater. It is recommended that installation be performed by a licensed electrician.

4.1 Unpacking

Carefully remove the heater and all components from the packaging. Inspect for any signs of damage. If damage is found, do not proceed with installation and contact your supplier.

4.2 Mounting Options

The heater can be mounted on a wall or ceiling. An adjustable bracket is included to direct heat as desired. An optional recess kit is available for flush mounting (sold separately).

  • Wall Mounting: Minimum clearance of 72 inches (183 cm) from the heater to any combustible material above.
  • Ceiling Mounting: Minimum clearance of 96 inches (244 cm) from the heater to any combustible material above.
Diagram showing heating coverage area for 4000W heater

Figure 3: Heating coverage diagram for the 4000W model, illustrating an approximate heated area of 130 sq ft (12 m²).

4.3 Electrical Connection

The heater requires a dedicated 220V-240V circuit. The electrical connection must be hardwired by a qualified electrician. Ensure all wiring complies with local and national electrical codes.

  • Voltage: 220-240V
  • Amperage: Approximately 16.6A
  • Circuit Breaker: A dedicated circuit breaker is required.

Refer to the detailed wiring diagrams provided in the separate installation guide for specific electrical connection instructions.

5. Operating Instructions

Once properly installed and connected to power, your Bromic Tungsten Smart Heat heater is ready for operation.

5.1 Powering On/Off

The heater elements can be controlled via a simple on/off switch. This switch is not included with the heater and must be installed by a qualified electrician as part of the electrical setup.

5.2 Heat Control (Optional)

For advanced heat control, the heater is compatible with external dimmer switches or smart control systems (not included). These systems allow for remote on/off functionality and adjustment of heat output. Consult with your electrician regarding compatible control systems.

5.3 Initial Operation

Upon first use, a slight odor or smoke may be emitted as manufacturing residues burn off. This is normal and should dissipate within a short period. Ensure adequate ventilation during initial operation.

6. Maintenance

Regular maintenance ensures optimal performance and longevity of your heater. Always disconnect power to the heater before performing any maintenance.

6.1 Cleaning

  • Allow the heater to cool completely before cleaning.
  • Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals.
  • Periodically inspect the heating elements for dust or debris. Use a soft brush or compressed air to gently remove any accumulation.

6.2 Inspection

Periodically check the mounting brackets and electrical connections for any signs of wear, damage, or loosening. Address any issues promptly to prevent hazards.

7. Troubleshooting

If you experience issues with your heater, refer to the following common problems and solutions:

Problem Possible Cause Solution
Heater does not turn on. No power supply, tripped circuit breaker, faulty switch, loose wiring. Check power supply. Reset circuit breaker. Verify switch operation. Consult a qualified electrician to inspect wiring.
Heater produces insufficient heat. Incorrect heat setting (if using dimmer), heater too far from target area, environmental factors (wind). Adjust dimmer setting. Ensure heater is positioned optimally for coverage (refer to Figure 3). Consider windbreaks for windy conditions.
Unusual odors or smoke after initial use. Residues burning off from manufacturing process. This is normal during initial operation and should dissipate. Ensure good ventilation. If persistent, disconnect power and contact support.

For issues not listed here or if troubleshooting steps do not resolve the problem, contact Bromic Heating customer support or a qualified electrician.

8. Specifications

Feature Detail
BrandBromic Heating
Model NumberBH0420032
Power Output4000 Watts
Voltage220-240 Volts
Amperage16.6 Amps
Fuel TypeElectric
Burner TypeRadiant (Infrared)
Heating CoverageApproximately 130-160 square feet (12-15 m²)
ColorBlack
Product Dimensions (DxWxH)3.5"D x 44"W x 8.5"H (8.9 cm D x 111.8 cm W x 21.6 cm H)
Item Weight20 pounds (9.07 kg)
Mounting TypeWall, Ceiling, Flush (with optional kit)
Indoor/Outdoor UsageOutdoor
Water Ingress RatingIPX4
UPC023509011995

9. Warranty & Support

The Bromic Tungsten Smart Heat 4000W Electric Patio Heater is backed by a comprehensive manufacturer's warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Bromic Heating website.

Customer Support:

For technical assistance, troubleshooting, or warranty claims, please contact Bromic Heating customer support. Contact information can typically be found on the product packaging, the official website, or in the included documentation.

Website: www.bromic.com (Please refer to your product documentation for the most accurate contact information.)

© 2023 Bromic Heating. All rights reserved.

This manual is subject to change without notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.