Adcraft PW-120H

Download PDF
Contents

Adcraft PW-120H Heater Proofer Control Drawer Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the safe and efficient operation, installation, maintenance, and troubleshooting of the Adcraft PW-120H Heater Proofer Control Drawer. Please read this manual thoroughly before operating the unit and retain it for future reference. Proper use ensures optimal performance and longevity of your equipment.

2. Safety Information

  • Electrical Safety: Ensure the unit is connected to a properly grounded 120V, 15 Amp electrical outlet. Do not operate with a damaged power cord or plug.
  • Hot Surfaces: The unit generates heat. Exercise caution when operating and allow sufficient time for cooling before cleaning or maintenance.
  • Water Pan: Always ensure the water pan is correctly positioned and filled as required for proofing functions.
  • Ventilation: Ensure adequate ventilation around the unit to prevent overheating.
  • Authorized Personnel: Only trained and authorized personnel should operate and maintain this equipment.
  • Cleaning: Disconnect power before cleaning. Use mild, non-abrasive cleaners.

3. Product Overview

The Adcraft PW-120H is a Heater Proofer Control Drawer designed to provide precise temperature and humidity control for heater proofer cabinets. It features an LED thermostat for easy monitoring and adjustment without opening the cabinet door. This unit is compatible with most major brands of heater proofer cabinets.

Adcraft PW-120H Heater Proofer Control Drawer with temperature and humidity controls.
Figure 1: Adcraft PW-120H Heater Proofer Control Drawer. This image displays the Adcraft PW-120H Heater Proofer Control Drawer. The front panel features a power switch, a digital display for temperature, a rotary dial for heat temperature control (labeled 'HEAT' and 'PROOF' with settings from OFF to 6), and another rotary dial for humidity control (labeled 'HUMIDITY' with settings from OFF to 5). A stainless steel water pan is visible on the top surface.

Control Panel Components:

  • Power Switch: Toggles the unit's power ON/OFF.
  • Temperature Display: LED screen showing the current internal temperature.
  • Heat/Proof Control Dial: Adjusts the heating element for temperature control. Settings range from OFF to 6, with indicators for 'HEAT' and 'PROOF' modes.
  • Humidity Control Dial: Adjusts the humidity level. Settings range from OFF to 5, labeled 'HUMIDITY'.

4. Setup

  1. Unpacking: Carefully remove the control drawer from its packaging. Inspect for any shipping damage. Report any damage to the carrier immediately.
  2. Placement: Install the control drawer into a compatible heater proofer cabinet. Ensure it is securely seated and properly aligned.
  3. Electrical Connection: Connect the power cord to a dedicated 120V, 15 Amp, grounded electrical outlet. Verify that the power supply matches the unit's requirements.
  4. Water Pan (for Proofing): If using the proofing function, ensure the water pan is clean and filled with distilled water to the recommended level.

5. Operating Instructions

5.1. Initial Start-up

  1. Ensure the unit is properly installed and connected to power.
  2. Turn the Power Switch to the 'ON' position. The LED temperature display will illuminate.

5.2. Heating Operation

  1. Turn the Heat/Proof Control Dial to the desired temperature setting within the 'HEAT' range. The temperature range is 80°F to 185°F.
  2. Monitor the LED display to ensure the unit reaches and maintains the set temperature.

5.3. Proofing Operation

  1. Ensure the water pan is filled with water.
  2. Turn the Heat/Proof Control Dial to the desired setting within the 'PROOF' range.
  3. Adjust the Humidity Control Dial to achieve the desired humidity level, which ranges from 30% to 100%.
  4. Regularly check the water level in the pan during extended proofing cycles.

5.4. Shut Down

  1. Turn both the Heat/Proof Control Dial and Humidity Control Dial to the 'OFF' position.
  2. Turn the Power Switch to the 'OFF' position.
  3. Allow the unit to cool completely before cleaning or moving.

6. Maintenance

6.1. Daily Cleaning

  1. Disconnect the unit from power.
  2. Remove the water pan and clean it with warm, soapy water. Rinse thoroughly and dry.
  3. Wipe down the exterior surfaces of the control drawer with a damp cloth and mild detergent. Avoid abrasive cleaners or scouring pads.
  4. Ensure all surfaces are dry before reconnecting power.

6.2. Regular Inspection

  • Periodically inspect the power cord for any signs of damage.
  • Check that all controls operate smoothly.
  • Ensure the unit is free from debris or obstructions.

7. Troubleshooting

ProblemPossible CauseSolution
Unit does not power onNo power supply; Power switch off; Faulty cord/plugCheck power outlet; Ensure power switch is ON; Inspect and replace cord/plug if damaged.
Unit not heating/proofingHeat/Proof dial set to OFF; Incorrect temperature/humidity setting; Heating element issueAdjust Heat/Proof dial; Verify settings; Contact service if issue persists.
Insufficient humidityWater pan empty; Humidity dial set too low; Water pan not properly seatedFill water pan; Adjust Humidity dial; Ensure water pan is correctly placed.
Temperature inconsistentCabinet door not sealed; Unit overloaded; Sensor issueCheck cabinet door seal; Reduce load; Contact service.

For issues not resolved by the above steps, please contact Adcraft customer support or a qualified service technician.

8. Specifications

  • Model: PW-120H
  • Brand: Adcraft
  • Power: 120V, 1800W, 15 Amps
  • Temperature Range: 80°F - 185°F
  • Humidity Range: 30% - 100%
  • Dimensions (W x D x H): 18.25 inches x 28 inches x 7 inches
  • Weight: Approximately 21 Pounds
  • Certifications: CE certified

9. Warranty and Support

The Adcraft PW-120H Heater Proofer Control Drawer is backed by Adcraft's 1-year replace or repair warranty. For warranty claims, technical support, or service inquiries, please contact Adcraft customer service. Ensure you have your model number (PW-120H) and purchase information available when contacting support.

Manufacturer: Adcraft

For the most current support information, please visit the official Adcraft website or refer to your purchase documentation.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.