Manuals+

X-PRO 286-999002

X-PRO 12V 35/35W Head Light Bulb Xenon User Manual

Model: 286-999002

1. Introduction

This manual provides essential information for the safe and effective use of your X-PRO 12V 35/35W Head Light Bulb Xenon. Designed for scooters, ATVs, and Go Karts, this bulb offers bright and long-lasting illumination. Please read this manual thoroughly before installation and operation.

2. Product Features

  • Head Light Bulb for Scooters, ATVs, Go Karts.
  • Specification: 12V, 35/35W.
  • Filled with Xenon gas for enhanced performance.
  • Provides bright light and ensures long-lasting operation.

3. Safety Information

WARNING:

  • Always disconnect the vehicle's battery before attempting any electrical work to prevent electric shock.
  • Allow the old bulb to cool down completely before handling, as it can be extremely hot.
  • Avoid touching the glass part of the new bulb with bare hands. Oils from your skin can create hot spots and reduce bulb life. Use clean gloves or a cloth.
  • Ensure the replacement bulb matches the vehicle's specifications (voltage, wattage, and base type).
  • If unsure about the installation process, consult a qualified mechanic or refer to your vehicle's service manual.
  • Keep out of reach of children.

4. Setup and Installation

This section outlines the general steps for replacing a headlight bulb. Specific procedures may vary depending on your vehicle model. Always refer to your vehicle's owner's manual for detailed instructions.

  1. Preparation: Park your vehicle on a level surface, turn off the engine, and engage the parking brake. Ensure the headlights are off and cool.
  2. Access the Headlight Assembly: Depending on your vehicle, you may need to open the hood/front panel or access the headlight from behind the fairing. Some vehicles may require removal of other components to gain access.
  3. Disconnect Power: Locate the electrical connector attached to the back of the headlight bulb. Gently squeeze or unclip the connector and pull it off.
  4. Remove Retaining Mechanism: Headlight bulbs are typically held in place by a spring clip, a twist-lock mechanism, or a retaining ring. Carefully disengage this mechanism.
  5. Remove Old Bulb: Grasp the base of the old bulb (not the glass) and carefully pull it straight out. Dispose of the old bulb responsibly.
  6. Install New Bulb: Holding the new X-PRO bulb by its base (using gloves or a clean cloth), align the tabs on the bulb with the notches in the headlight housing. Gently push the bulb straight in until it is seated firmly.
  7. Secure Bulb: Re-engage the retaining mechanism to secure the new bulb in place.
  8. Reconnect Power: Reattach the electrical connector to the back of the new bulb, ensuring it clicks securely into place.
  9. Test Functionality: Reconnect the vehicle's battery (if disconnected) and turn on the headlights to verify proper operation. Check both high and low beams.
  10. Reassemble: Reinstall any components that were removed to access the headlight.
X-PRO 12V 35/35W Head Light Bulb Xenon

Figure 4.1: X-PRO 12V 35/35W Head Light Bulb Xenon. This image shows the compact design of the bulb, featuring a blue-tinted glass envelope and a metallic base with electrical contacts, ready for installation.

5. Operating Instructions

Once the X-PRO 12V 35/35W Head Light Bulb Xenon is correctly installed, its operation is integrated with your vehicle's electrical system. Simply turn on your vehicle's ignition and activate the headlight switch as you normally would. The bulb will illuminate, providing the necessary light for safe operation.

6. Maintenance

The X-PRO Head Light Bulb Xenon is designed for long-lasting performance with minimal maintenance. However, periodic checks can help ensure optimal illumination:

  • Regular Inspection: Periodically check your headlights to ensure both high and low beams are functioning correctly.
  • Cleaning: If the headlight lens becomes dirty, clean it with a soft, damp cloth. Avoid abrasive cleaners that could scratch the lens.
  • Bulb Replacement: If the bulb dims significantly or fails, replace it following the installation steps outlined in Section 4. Always replace bulbs in pairs if possible, as bulbs of similar age tend to fail around the same time.

7. Troubleshooting

If your X-PRO Head Light Bulb Xenon is not functioning as expected, consider the following troubleshooting steps:

ProblemPossible CauseSolution
Bulb does not light up.
  • Loose electrical connection.
  • Blown fuse.
  • Incorrect installation.
  • Defective bulb.
  • Check and secure the electrical connector.
  • Inspect and replace any blown fuses in the vehicle's fuse box.
  • Re-check installation steps (Section 4) to ensure proper seating and connection.
  • Replace the bulb with a new one.
Bulb is dim or flickers.
  • Poor electrical contact.
  • Aging bulb.
  • Voltage issue in vehicle's electrical system.
  • Ensure connections are clean and tight.
  • Consider replacing the bulb.
  • Consult a qualified mechanic to diagnose electrical system issues.

If problems persist after attempting these solutions, it is recommended to consult a qualified vehicle technician.

8. Specifications

AttributeValue
BrandX-PRO
Model Number286-999002
Voltage12V
Wattage35/35W
Bulb TypeXenon Head Light Bulb
Item Weight0.798 ounces
Package Dimensions5.3 x 2.8 x 0.9 inches
First AvailableAugust 28, 2014

9. Warranty and Support

For warranty information and customer support regarding your X-PRO 12V 35/35W Head Light Bulb Xenon, please contact X-PRO directly through their official website or the retailer from whom you purchased the product. Keep your proof of purchase for any warranty claims.

X-PRO Brand Logo

X-PRO is committed to providing quality powersports accessories and parts.

Visit the X-PRO Store on Amazon for more products and information.