Hakko FH200-01 Iron Holder User Manual

1. Introduction

This manual provides comprehensive instructions for the safe and effective use, setup, maintenance, and troubleshooting of the Hakko FH200-01 Iron Holder with 599B. The FH200-01 is designed to securely hold your soldering iron when not in use and includes an integrated tip cleaning system for optimal soldering performance.

2. Safety Information

While the FH200-01 is a passive holder, it is used in conjunction with hot soldering irons. Always observe the following safety precautions:

• Always place the hot soldering iron securely in the holder when not in use to prevent accidental burns or damage.
• Ensure the holder is placed on a stable, heat-resistant surface.
• Keep the holder and soldering station away from flammable materials.
• Allow the soldering iron to cool completely before storing or performing maintenance on the holder.
• Do not touch the hot tip of the soldering iron or the inside of the holder immediately after use.

3. Package Contents

Verify that all components are present upon unpacking:

• Hakko FH200-01 Iron Holder Base
• 599B Tip Cleaning Wire (Brass Wool)
• Removable Drip Tray

4. Setup

Follow these steps to set up your Hakko FH200-01 Iron Holder:

1. Unpack all components from the packaging.
2. Insert the 599B tip cleaning wire into the gold-colored pot on the holder base. Ensure it sits securely.
3. Place the removable drip tray underneath the tip cleaning pot. This tray collects excess solder and flux residue.
4. Position the assembled iron holder on a stable, flat, and heat-resistant workbench surface, within easy reach of your soldering station.

Figure 1: The Hakko FH200-01 Iron Holder, featuring its blue base, gold-colored tip cleaning pot with brass wool (599B), and the yellow iron rest spring. This image illustrates the fully assembled unit ready for use.

5. Operating Instructions

Using the Hakko FH200-01 Iron Holder is straightforward:

• Holding the Iron: When not actively soldering, place the hot soldering iron into the yellow spring coil of the holder. Ensure the tip is positioned over the 599B cleaning wire pot.
• Tip Cleaning: To clean the soldering iron tip, gently insert the hot tip into the 599B brass wool. Rotate or rub the tip against the brass wool to remove excess solder and oxidation. The brass wool effectively cleans the tip without significantly lowering its temperature, unlike traditional wet sponges.
• Drip Tray Function: The removable drip tray catches any solder or flux residue that falls from the tip during cleaning, keeping your workspace clean.

6. Maintenance

Regular maintenance ensures the longevity and effectiveness of your iron holder:

• Cleaning the 599B: Over time, the brass wool will accumulate solder and flux residue. Periodically remove the 599B from its pot and shake out the debris. If heavily soiled, the 599B can be replaced.
• Emptying the Drip Tray: Regularly remove and empty the drip tray of accumulated solder and flux. Wipe it clean with a dry cloth.
• General Cleaning: Wipe down the exterior of the iron holder with a damp cloth to remove dust and grime. Ensure the holder is completely cool before cleaning. Do not use abrasive cleaners or solvents.

7. Troubleshooting

Common issues and their solutions:

• Iron not sitting securely:

  Ensure the soldering iron handle is properly seated in the yellow spring coil. Verify that the holder is on a level surface.

• Tip not cleaning effectively:

  Check if the 599B brass wool is heavily saturated with solder. If so, clean it or replace it. Ensure the tip is hot enough for effective cleaning.
• Excessive solder on workbench:

  Ensure the drip tray is correctly positioned under the 599B pot. Empty the drip tray regularly.

8. Specifications

9. Warranty and Support

For warranty information or technical support regarding your Hakko FH200-01 Iron Holder, please contact Hakko customer service or the authorized reseller from whom you purchased the product. Refer to the official Hakko website for the most up-to-date contact information.

If you require additional details or assistance, please do not hesitate to contact the seller or manufacturer directly.