Mr Beams MB370

Mr. Beams MB370 Wireless LED Remote Control Spotlight User Manual

Model: MB370

1. Introduction

Thank you for choosing the Mr. Beams MB370 Wireless LED Remote Control Spotlight. This battery-powered spotlight is designed to provide bright, motion-activated illumination for various outdoor and indoor areas. Featuring a motion sensor, photocell, and remote control, it offers versatile lighting solutions for security, convenience, and safety. Please read this manual thoroughly before installation and operation to ensure proper use and longevity of your product.

2. Package Contents

Verify that all components are present in your package:

  • Mr. Beams MB370 Wireless LED Spotlight
  • Remote Control
  • Mounting Hardware (screws and anchors)
  • User Manual

Note: Batteries are not included and must be purchased separately. The spotlight requires 3 D-cell batteries, and the remote control requires 2 AAA batteries.

3. Important Safety Information

  • Do not mix old and new batteries.
  • Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
  • Always insert batteries with the correct polarity (+ and -).
  • Dispose of used batteries properly according to local regulations.
  • Do not submerge the unit in water. While weather-resistant, it is not waterproof.
  • Do not stare directly into the LED light.
  • Ensure the mounting surface is stable and can support the weight of the spotlight.

4. Setup and Installation

4.1 Battery Installation

  1. Spotlight: Twist the back cover of the spotlight counter-clockwise to open the battery compartment. Insert 3 D-cell batteries, ensuring correct polarity. Replace the cover and twist clockwise to secure.
  2. Remote Control: Open the battery compartment on the back of the remote. Insert 2 AAA batteries, ensuring correct polarity. Close the compartment.

4.2 Mounting the Spotlight

The MB370 spotlight is designed for wall mounting. Choose a location that provides optimal coverage and is within range of the remote control (up to 30 feet).

  1. Select a desired mounting location. The spotlight can be installed on walls, eaves, or other flat surfaces.
  2. Use the mounting bracket as a template to mark the screw holes.
  3. Drill pilot holes if necessary, and insert wall anchors if mounting into drywall or masonry.
  4. Secure the mounting bracket to the surface using the provided screws.
  5. Attach the spotlight to the mounting bracket, ensuring it clicks securely into place.
  6. Adjust the angle of the spotlight to direct the light as needed.
Mr. Beams MB370 spotlight mounted on a wall next to a door, illuminating the entrance.

Image: Mr. Beams MB370 spotlight mounted on a wall next to a door, illuminating the entrance. This demonstrates a typical installation scenario for the spotlight.

5. Operating Instructions

5.1 Motion Sensor Operation

The spotlight features a built-in motion sensor that activates the light when movement is detected within its range (up to 3 feet). The integrated photocell ensures the light only activates in low-light conditions to conserve battery life.

  • When motion is detected in darkness, the spotlight will turn on automatically.
  • The default auto shut-off setting for motion activation is 3 seconds after motion ceases.

5.2 Remote Control Functions

The remote control allows for manual operation and adjustment of settings.

Mr. Beams MB370 spotlight with its remote control, showing buttons for ON, OFF, brightness, and motion sensor settings.

Image: Mr. Beams MB370 spotlight with its remote control, showing buttons for ON, OFF, brightness, and motion sensor settings. This illustrates the product and its control unit.

  • ON Button: Press to manually turn the spotlight ON.
  • OFF Button: Press to manually turn the spotlight OFF.
  • Brightness Settings: The remote allows you to cycle through three brightness levels: 60, 90, or 140 lumens. Press the brightness button to adjust.
  • Auto Shut-Off Timer: When manually activated with the remote, you can set the light to turn off after 1 hour or 4 hours. Consult the remote's specific button for this function.
  • Motion Sensor Activation: The remote can also be used to enable or disable the motion sensor functionality.
A person using the remote control to activate a Mr. Beams spotlight mounted outside a door.

Image: A person using the remote control to activate a Mr. Beams spotlight mounted outside a door. This demonstrates the practical use of the remote control.

6. Maintenance

6.1 Battery Replacement

When the light output diminishes or the unit stops functioning, it is time to replace the batteries. Follow the battery installation steps in Section 4.1.

6.2 Cleaning

Wipe the spotlight and remote control with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these may damage the unit.

7. Troubleshooting

ProblemPossible CauseSolution
Light does not turn on.1. Dead or incorrectly installed batteries.
2. Motion sensor obstructed or dirty.
3. Ambient light too bright (photocell preventing activation).		1. Replace batteries, ensuring correct polarity.
2. Clean sensor lens. Ensure no obstructions are blocking the sensor.
3. Test in a darker environment.
Light stays on continuously.1. Constant motion in sensor range.
2. Sensor malfunction.
3. Extreme cold weather affecting sensor.		1. Relocate the spotlight or adjust its angle to avoid constant motion.
2. Remove and reinsert batteries. If problem persists, contact support.
3. In very cold climates, battery performance and sensor accuracy may be reduced.
Remote control not working.1. Dead or incorrectly installed batteries.
2. Out of range.
3. Obstruction between remote and spotlight.		1. Replace AAA batteries in the remote, ensuring correct polarity.
2. Move closer to the spotlight (within 30 feet).
3. Ensure a clear line of sight between the remote and the spotlight.

8. Specifications

  • Model: MB370
  • Brand: Mr Beams
  • Light Source: LED
  • Lumens: 60, 90, 140 (adjustable)
  • Light Color: Cool White (5000 Kelvin)
  • Power Source: Battery Powered (Spotlight: 3 D-cell, Remote: 2 AAA)
  • Motion Sensor Range: Up to 3 feet
  • Auto Shut-Off (Motion): 3 seconds after motion stops
  • Auto Shut-Off (Remote): 1 hour or 4 hours
  • Controller Type: Remote Control
  • Indoor/Outdoor Usage: Outdoor
  • Material: Plastic
  • Color: White
  • Item Weight: 0.7 Pounds
  • Installation Type: Wall Mount / Flush Mount

9. Warranty and Support

For warranty information and customer support, please refer to the documentation included with your purchase or visit the official Mr. Beams website. Keep your proof of purchase for any warranty claims.

If you encounter any issues not covered in this manual, please contact Mr. Beams customer service for assistance.

© 2023 Mr. Beams. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.