Xantrex PROwatt SW 2000I True Sinewave Inverter User Manual
Model: 806-1220-01
1. Introduction
This manual provides essential information for the safe and efficient operation of your Xantrex PROwatt SW 2000I True Sinewave Inverter. This device converts 12VDC battery power into 230VAC true sinewave electricity, suitable for powering sensitive electronics and appliances. Please read this manual thoroughly before installation and use.
2. Safety Information
WARNING: Risk of Electric Shock, Fire, or Explosion.
- Always disconnect the battery before working on the inverter or connected equipment.
- Ensure proper ventilation around the inverter to prevent overheating.
- Do not expose the inverter to water, rain, or excessive moisture.
- Use appropriate wire gauges for DC input and AC output connections.
- This inverter must be installed by a qualified professional in accordance with all applicable electrical codes.
- Do not operate the inverter if it has been damaged in any way.
3. Product Overview
The Xantrex PROwatt SW 2000I is designed for robust performance in various applications, including recreational vehicles, boats, and trucks. It provides clean, reliable AC power from a 12VDC source.
3.1 Front Panel Features
Figure 1: Xantrex PROwatt SW 2000I Front Panel
- Power Button: Turns the inverter ON/OFF.
- Digital Display: Shows input voltage, output power, and fault codes.
- Status Indicators: LEDs for Power, Fault, and Remote status.
- AC Outlet: 230VAC output for connecting appliances.
- Remote Port: For connecting an optional remote ON/OFF switch.
3.2 Rear Panel Features
Figure 2: Xantrex PROwatt SW 2000I Rear Panel (similar to front view, but illustrates overall unit)
- DC Input Terminals: Positive (+) and Negative (-) terminals for 12VDC battery connection.
- Cooling Fan: Automatically activates to maintain optimal operating temperature.
- Ground Terminal: For chassis grounding.
4. Setup and Installation
Proper installation is crucial for the safe and efficient operation of your inverter. Refer to the full installation guide for detailed wiring diagrams.
4.1 Mounting Location
- Mount the inverter in a dry, cool, and well-ventilated area.
- Avoid locations exposed to direct sunlight, heat sources, or moisture.
- Ensure sufficient clearance around the inverter for airflow.
- Mount on a non-combustible surface.
4.2 DC Wiring
- Ensure the battery bank is fully charged and disconnected from any charging sources.
- Connect the negative (-) terminal of the inverter to the negative (-) terminal of the battery bank using appropriate gauge cable.
- Connect the positive (+) terminal of the inverter to the positive (+) terminal of the battery bank via a properly rated DC fuse or circuit breaker.
- Secure all connections tightly to prevent loose contacts and voltage drops.
4.3 AC Wiring
- Connect your 230VAC appliances directly to the AC outlet on the front panel.
- For hardwired installations, consult a qualified electrician.
- Ensure the total wattage of connected appliances does not exceed the inverter's continuous power rating (2000W).
5. Operating Instructions
5.1 Turning the Inverter ON/OFF
- Press and hold the Power button on the front panel for approximately 1-2 seconds until the display illuminates and the Power LED turns green.
- To turn OFF, press and hold the Power button again until the display turns off.
- If using a remote switch, refer to the remote switch manual for operation.
5.2 Monitoring Operation
The digital display cycles through various operational parameters:
- Input Voltage (V): Displays the current DC input voltage from the battery.
- Output Power (W): Shows the current AC power being drawn by connected appliances.
- Fault Codes: In case of an error, a specific fault code will be displayed. Refer to the Troubleshooting section.
6. Maintenance
The Xantrex PROwatt SW 2000I is designed for minimal maintenance. However, regular checks can ensure long-term performance.
- Cleaning: Periodically clean the exterior of the inverter with a dry, soft cloth. Do not use liquid cleaners.
- Ventilation: Ensure cooling vents are free from dust and obstructions. Use compressed air to clear dust if necessary.
- Connections: Annually check all DC and AC connections for tightness. Loose connections can cause overheating and poor performance.
- Battery Health: Maintain your battery bank according to the battery manufacturer's recommendations. A healthy battery is essential for inverter performance.
7. Troubleshooting
This section provides solutions to common issues. For more complex problems, contact Xantrex technical support.
| Problem | Possible Cause | Solution |
|---|---|---|
| Inverter does not turn ON | No DC input power; Low battery voltage; Blown DC fuse/breaker; Loose connections. | Check battery connections; Charge battery; Check/replace fuse/breaker; Tighten connections. |
| No AC output | Overload; Over-temperature; Low/High input voltage; Fault condition. | Reduce load; Allow inverter to cool; Check battery voltage; Refer to fault codes on display. |
| Inverter shuts down frequently | Battery voltage too low under load; Excessive load; Poor ventilation. | Charge battery; Reduce load; Improve ventilation. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Name | 806-1220-01 |
| Continuous Power | 2000W |
| Input Voltage | 12VDC |
| Output Voltage | 230VAC True Sinewave |
| Item Dimensions (LxWxH) | 19 x 11 x 7 inches |
| Item Weight | 14 Pounds |
| Material | Plastic |
| Recommended Uses | Boat, Recreational Vehicle, Truck |
9. Warranty and Support
The Xantrex PROwatt SW 2000I Inverter is covered by a manufacturer's warranty. Please refer to the warranty card included with your product for specific terms and conditions.
For technical support, service, or warranty claims, please contact Xantrex customer service through their official website or the contact information provided in your product packaging. When contacting support, please have your model number (806-1220-01) and serial number ready.
You can visit the official Xantrex Store on Amazon for more information: Xantrex Store
