Project E Beauty Skin Scrubber PE066 User Manual

Introduction

The Project E Beauty Skin Scrubber PE066 is a device designed for facial skin care, utilizing ultrasonic vibrations to cleanse, exfoliate, and enhance the absorption of skincare products. This manual provides detailed instructions for safe and effective use of your device.

Safety Information

• Read all instructions before using the device.
• Keep the device away from water or excessive moisture.
• Do not use on broken, irritated, or infected skin.
• Consult a physician before use if you have any skin conditions, medical implants, or are pregnant.
• Keep out of reach of children.
• Do not disassemble or attempt to repair the device.
• Use only the provided charging cable.

Product Overview

The Project E Beauty Skin Scrubber PE066 features a stainless steel spatula and a control panel for mode selection and power.

Image: The Project E Beauty Skin Scrubber PE066 shown with its retail packaging, highlighting the device's design and key features.

Key Features:

• Ultrasonic Vibrations: For deep cleansing and exfoliation.
• Iontophoresis: Enhances absorption of skincare products.
• Three Modes: Extract, Infuse, Massage.
• Wireless Operation: For convenience and portability.
• Suitable for All Skin Types: Gentle and effective.

Image: The Project E Beauty Skin Scrubber PE066 with text overlays indicating its key features: 3 modes, double-sided spatula, wireless, and suitability for all skin types.

Setup

Charging the Device:

1. Ensure the device is turned off.
2. Connect the charging cable to the device's charging port.
3. Plug the other end of the cable into a suitable USB power adapter (not included).
4. The charging indicator light will illuminate. Charge the device fully before first use, typically for 2-3 hours.
5. Disconnect the charger once fully charged.

Operating Instructions

The Project E Beauty Skin Scrubber PE066 offers three distinct modes for comprehensive skincare. For optimal results, follow these steps:

Image: A visual guide illustrating the seven steps for using the Project E Beauty Skin Scrubber, from cleansing to ultrasonic penetration and massage.

1. Step 1: Cleanse

   Begin by thoroughly cleansing your face to remove makeup and surface impurities. Use your preferred facial cleanser.

2. Step 2: Dampen Face

   Ensure your face is damp. You can use water, a facial mist, or a toner. The device requires a moist surface to work effectively.

3. Step 3: Extraction Mode (Deep Cleansing & Exfoliation)

   Turn on the device and select the "Extraction" mode. Gently glide the spatula across your damp skin, with the tip angled downwards, to loosen and remove blackheads, whiteheads, and dead skin cells. Move slowly, focusing on areas with congestion.

4. Step 4: Apply Nourishing Skincare

   After extraction, apply your preferred serum, essence, or moisturizer to your face. Do not let your skin dry completely.

5. Step 5: Infusion Mode (Product Absorption)

   Switch the device to "Infusion" mode. With the spatula flat against your skin, gently move it upwards over your face. This mode uses iontophoresis to help skincare products penetrate deeper into the skin.

6. Step 6: Reapply Nourishing Skincare (Optional)

   If your skin feels dry during the infusion process, you may reapply a small amount of serum or mist to maintain moisture.

7. Step 7: Ultrasonic Penetration + Massage Mode

   Select the "Massage" mode. Continue to glide the spatula over your face in an upward motion. This mode combines ultrasonic vibrations with a gentle massage to further enhance product absorption and promote circulation.

Important: Always keep your skin moist during use. Do not press too hard or hold the device in one spot for too long.

Maintenance

Cleaning the Device:

1. After each use, turn off the device.
2. Wipe the stainless steel spatula clean with a soft, damp cloth or an alcohol wipe.
3. Do not rinse the entire device under water. The main body is not waterproof.
4. Ensure the device is completely dry before storing.

Storage:

• Store the device in a cool, dry place, away from direct sunlight and extreme temperatures.
• Keep it in its original packaging or a protective pouch to prevent damage.

Troubleshooting

Specifications

• Model: PE066
• Brand: Project E Beauty
• Dimensions: 7.48 x 4.72 x 1.57 inches
• Weight: 9.88 ounces
• Power Source: Rechargeable Battery (USB charging)
• Material: Stainless Steel Spatula, ABS Body
• Functions: Ultrasonic Cleansing, Exfoliation, Iontophoresis (Product Infusion), Massage

Warranty and Support

For warranty information or technical support, please contact Project E Beauty customer service. Refer to the product packaging or the official Project E Beauty website for the most current contact details.

Manufacturer: Project E Beauty