Introduction
Thank you for choosing the TECTRO TBH 570 Red Pellet Stove. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your new pellet stove. Please read this manual thoroughly before installation and use, and keep it for future reference.

Figure 1: TECTRO TBH 570 Red Pellet Stove. This image shows the TECTRO TBH 570 pellet stove in red, viewed from the front-right angle. The black door with a glass panel reveals a visible flame inside the combustion chamber. The top surface is black, and the side panels are red with vertical ventilation slits.
Safety Information
Always adhere to local building codes and regulations when installing and operating this appliance. Failure to do so may result in fire, property damage, personal injury, or death.
- Do not store fuel or other flammable vapors and liquids in the vicinity of the appliance.
- Ensure proper ventilation.
- Keep children and pets away from the hot surfaces of the stove.
- Only use approved wood pellets as fuel.
- Regularly inspect and clean the chimney and flue pipes.
Setup and Installation
The TECTRO TBH 570 is designed for freestanding installation and is not suitable for wall mounting. Professional installation is recommended.
Unpacking
- Carefully remove the stove from its packaging.
- Inspect for any shipping damage. Contact your dealer immediately if damage is found.
- Ensure all components listed in the packing list are present.
Placement
- Place the stove on a non-combustible surface.
- Maintain minimum clearances to combustible materials as specified by local codes.
- Ensure easy access for maintenance and cleaning.
Ventilation and Flue Connection
- The stove features a rear smoke outlet with a diameter of Ø 8 cm.
- An air intake with a diameter of Ø 5 cm is present. Ensure adequate fresh air supply for combustion.
- Connect the stove to a suitable chimney or flue system according to local regulations.
Operating Instructions
Fuel Loading
- The pellet tank capacity is 13 kg.
- Only use high-quality wood pellets.
- Open the top lid and carefully pour pellets into the hopper.
Starting the Stove
- Ensure the pellet tank is filled and the brazier is clean.
- Use the digital control panel or the remote control to initiate the startup sequence.
- The stove will automatically feed pellets and ignite them.
Programming and Control
- The stove features digital programming for setting desired temperatures and operating times.
- Adjust the thermal power output (Min: 2.9 kW, Max: 7.4 kW) as needed.
- The remote control allows convenient adjustment of settings from a distance.
- A safety thermostat is integrated for safe operation.
- Forced ventilation helps distribute heat efficiently.
Shutting Down the Stove
- To turn off the stove, use the control panel or remote control.
- The stove will enter a cool-down cycle, stopping pellet feeding and continuing ventilation until safe temperatures are reached.
- Do not open the combustion chamber door until the stove has completely cooled down.
Maintenance
Regular maintenance is crucial for the longevity and efficient operation of your pellet stove.
Daily Maintenance
- Clean the Brazier: Remove ash and unburnt pellets from the brazier.
- Clean the Ash Pan: Empty the ash pan.
- Clean the Glass: The stove features self-cleaning glass, but occasional wiping with a damp cloth (when cold) may be necessary.
Weekly/Bi-Weekly Maintenance
- Vacuum the Combustion Chamber: Use a shop vacuum to remove ash from the combustion chamber and heat exchanger tubes.
- Inspect Gaskets: Check door and glass gaskets for wear and tear. Replace if necessary.
Annual Maintenance
- Chimney and Flue Cleaning: Have a qualified professional clean the chimney and flue pipes.
- Component Inspection: Inspect all internal components, including motors, fans, and electrical connections.
- Professional Service: Consider an annual professional service to ensure optimal performance and safety.
Troubleshooting
This section provides solutions to common issues you might encounter.
| Problem | Possible Cause | Solution |
|---|---|---|
| Stove does not ignite. | Empty pellet hopper, dirty brazier, faulty igniter. | Refill hopper, clean brazier, contact service for igniter replacement. |
| Low heat output. | Poor quality pellets, clogged flue, low power setting. | Use quality pellets, clean flue, increase power setting. |
| Excessive smoke. | Blocked chimney, wet pellets, insufficient air intake. | Check chimney for blockages, use dry pellets, ensure air intake is clear. |
If the problem persists after attempting these solutions, please contact qualified service personnel.
Specifications
| Feature | Detail |
|---|---|
| Model | TBH570 |
| Brand | TECTRO |
| Type | Ventilated Pellet Stove |
| Energy Class | A+ |
| Heating Capacity | Up to 170 m³ (65 m²) |
| Max Effective Thermal Power | 7 kW |
| Min Introduced Thermal Power | 2.9 kW |
| Max Introduced Thermal Power | 7.4 kW |
| Efficiency | 92.7% |
| Pellet Consumption | 0.6 - 1.7 kg/h |
| Tank Capacity | 13 kg |
| Dimensions (W x H x D) | 47 cm x 90 cm x 47.6 cm |
| Weight | 80 kg |
| Smoke Outlet Diameter | Ø 8 cm (Rear) |
| Air Intake Diameter | Ø 5 cm |
| Material (Structure/Coating) | Steel |
| Material (Brazier) | Cast Iron |
| Color | Red |
| Programmable | Yes (Digital) |
| Remote Control | Yes |
| Safety Thermostat | Yes |
| Forced Ventilation | Yes |
| Self-Cleaning Glass | Yes |
| Made in | Italy |
Warranty and Support
The TECTRO TBH 570 Pellet Stove comes with a 2-year warranty from the date of purchase. This warranty covers manufacturing defects and material faults under normal use and service conditions.
For warranty claims, technical support, or spare parts, please contact your authorized TECTRO dealer or visit the official TECTRO website for contact information. Please have your model number (TBH570) and purchase date available when contacting support.
For more information, visit: www.tectro.com





