1. Introduction
The Everbilt 1/6 HP Submersible Utility Pump (Model UT00801) is engineered for efficient water removal from various locations. This pump is ideal for draining sinks, tubs, and shallow flooded areas such as basements, floors, and flat roofs. Its submersible design allows it to operate directly in water, effectively reducing water levels down to 1/8 inch.
This manual provides essential information for the safe and effective use of your Everbilt utility pump. Please read all instructions carefully before installation and operation.
Figure 1: Everbilt 1/6 HP Submersible Utility Pump. This image displays the main unit of the pump, highlighting its compact, black plastic housing, the threaded discharge port, and the power cord connection point. A separate threaded adapter is also visible.
2. Safety Information
Always prioritize safety when operating electrical equipment, especially near water. Failure to follow these safety guidelines can result in electric shock, fire, personal injury, or property damage.
- Electrical Safety: Ensure the pump is connected to a properly grounded outlet. Do not use extension cords unless absolutely necessary and ensure they are rated for outdoor use and wet conditions. Never operate the pump with damaged cords or plugs.
- Submersible Use Only: This pump is designed for submersible operation. Do not run the pump dry, as this can cause severe damage to the motor.
- Water Temperature: Do not use this pump with water temperatures exceeding 104°F (40°C).
- Flammable Liquids: Never pump flammable or corrosive liquids. This pump is intended for water only.
- Children and Pets: Keep children and pets away from the pump and any standing water during operation.
- Maintenance: Always disconnect power before performing any maintenance or cleaning on the pump.
3. Package Contents
Verify that all components are present and undamaged upon unpacking.
- Everbilt 1/6 HP Submersible Utility Pump (Model UT00801)
- Threaded Hose Adapter
- Instruction Manual
4. Setup
- Attach Discharge Hose: Connect a standard garden hose or a suitable discharge pipe to the pump's threaded outlet. The pump includes a removable adapter to accommodate different hose sizes. Ensure a secure, leak-free connection.
- Position the Pump: Place the pump on a stable, level surface in the area to be drained. Ensure the intake screen at the bottom of the pump is clear of debris. The pump must be fully submerged in water for proper operation and cooling.
- Route Discharge Hose: Extend the discharge hose to a suitable drainage area, ensuring the water will not flow back into the area being drained. Avoid kinks or sharp bends in the hose that could restrict water flow.
- Power Connection: Plug the pump's power cord into a grounded 120V AC electrical outlet. The pump will begin operating immediately upon connection to power.
5. Operating Instructions
The Everbilt 1/6 HP Submersible Utility Pump is designed for continuous operation once plugged in, provided it remains submerged.
- Automatic Operation: This model operates continuously when plugged in. There is no on/off switch on the unit itself. Operation starts when power is supplied and stops when power is disconnected.
- Water Level: The pump is capable of removing water down to a minimum level of approximately 1/8 inch. For optimal performance, ensure the pump remains submerged during operation.
- Monitoring: Periodically check the pump's operation and the discharge area to ensure proper water flow and prevent accidental flooding.
- Disconnection: To stop the pump, simply unplug it from the electrical outlet.
6. Maintenance
Regular maintenance ensures the longevity and efficient performance of your pump.
- Cleaning Intake Screen: Regularly inspect and clean the intake screen at the bottom of the pump to prevent blockages from debris, which can reduce pumping efficiency.
- Storage: When not in use, clean the pump thoroughly and store it in a dry, frost-free location. Drain any remaining water from the pump and hose to prevent freezing damage.
- Inspection: Before each use, inspect the power cord, plug, and pump housing for any signs of damage. Do not use the pump if any damage is observed.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump does not start | No power; tripped circuit breaker; damaged cord/plug | Check power supply; reset breaker; inspect and replace damaged components. |
| Pump runs but does not pump water | Intake screen clogged; air lock; discharge hose kinked/blocked; pump not submerged | Clean intake screen; prime pump by submerging fully; clear hose; ensure pump is fully submerged. |
| Reduced water flow | Partial blockage in intake or hose; low voltage | Clean intake screen and hose; ensure stable power supply. |
| Pump cycles on and off rapidly | Insufficient water level; air in system | Ensure adequate water level for continuous operation; check for air leaks in connections. |
If troubleshooting steps do not resolve the issue, contact Everbilt customer support for assistance.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Everbilt |
| Model Number | UT00801 |
| Horsepower | 1/6 HP |
| Flow Rate | Up to 28 Gallons Per Minute (GPM) |
| Maximum Lifting Height | 0.13 Inches (Note: This value likely refers to the minimum water level the pump can achieve, not its maximum lift height.) |
| Minimum Water Level | 1/8 inch (approx.) |
| Item Weight | 5.71 Pounds |
| Product Dimensions | 7.68 x 6.89 x 10.63 inches |
| Power Source | AC/DC (Standard 120V AC for typical use) |
| Material | Plastic |
| Style | Submersible |
9. Warranty and Support
The Everbilt 1/6 HP Submersible Utility Pump comes with a 1-Year Limited Warranty. For warranty claims, technical support, or replacement parts, please contact Everbilt customer service directly. Keep your purchase receipt as proof of purchase.
For further assistance, refer to the official Everbilt website or contact their customer support line.
