1. Product Overview
The Everbilt 1/2 HP Submersible Sump Pump (Model SP05002VD) is designed for efficient water removal in residential sump applications. Constructed with a durable stainless steel motor housing and a rugged cast iron volute and seal plate, this pump ensures long-lasting performance. It features an oil-filled, high-efficiency PSC motor with permanent lubricated ball bearings for quiet, maintenance-free operation. The innovative reed sensor vertical float switch provides reliable automatic activation, and its top suction design helps filter debris and minimizes clogging.
Figure 1: Everbilt 1/2 HP Submersible Sump Pump. This image shows the black submersible pump unit with its integrated float switch and discharge port.
2. Important Safety Information
Read all instructions carefully before installation and operation. Failure to follow these instructions can result in serious injury or property damage. Keep this manual for future reference.
- Always disconnect power before servicing the pump.
- Ensure the pump is properly grounded to prevent electrical shock.
- Do not operate the pump in areas containing flammable liquids or gases.
- Keep hands and feet clear of the pump's intake and discharge openings during operation.
- This pump is designed for water only. Do not use for chemicals or other liquids.
3. Setup and Installation
Proper installation is crucial for the efficient and safe operation of your sump pump.
- Sump Pit Preparation: Ensure the sump pit is clean and free of debris. The pit should be large enough to accommodate the pump and allow for proper float switch movement.
- Positioning the Pump: Place the pump on a solid, level surface at the bottom of the sump pit. The top suction design helps filter debris and minimizes clogging, but ensure the intake is clear.
- Discharge Pipe Connection: Connect a discharge pipe (not included) to the pump's discharge port. Use appropriate fittings and sealants to ensure a watertight connection. A check valve is recommended to prevent backflow.
- Float Switch Adjustment: The innovative reed sensor vertical float switch is pre-set for optimal operation. Ensure the float can move freely without obstruction within the sump pit. The pump will activate when the water level rises and lifts the float.
- Power Connection: Connect the pump to a dedicated, grounded 120V AC electrical outlet. Do not use extension cords.
- Testing: Once installed, fill the sump pit with water to test the pump's operation. Verify that the pump activates, removes water, and shuts off automatically when the water level drops.
4. Operating Instructions
The Everbilt 1/2 HP Submersible Sump Pump operates automatically once properly installed and connected to power.
- The pump is designed to activate when the water level in the sump pit rises, lifting the vertical float switch.
- It will continue to pump water until the water level drops sufficiently, allowing the float switch to return to its off position.
- The oil-filled, high-efficiency PSC motor and permanent lubricated ball bearings ensure quiet and reliable performance.
- Regularly inspect the sump pit and pump for any obstructions or unusual operation.
5. Maintenance
While the Everbilt sump pump is designed for low maintenance, periodic checks are recommended to ensure optimal performance and longevity.
- Monthly Inspection:
- Disconnect power to the pump before inspection.
- Remove any debris from the sump pit that could obstruct the pump's intake or float switch.
- Check the float switch for free movement. Ensure it is not tangled or stuck.
- Inspect the power cord for any signs of damage.
- Briefly reconnect power and test the pump by pouring water into the pit to ensure it cycles on and off correctly.
- Annual Cleaning:
- Disconnect power and remove the pump from the sump pit.
- Clean the pump's exterior and intake screen to remove any accumulated sediment or debris.
- Inspect the discharge pipe and check valve for any blockages or leaks.
- Lubrication: The pump features permanent lubricated ball bearings and does not require additional lubrication.
6. Troubleshooting Guide
Refer to this guide for common issues and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump does not start. | No power; tripped circuit breaker; faulty float switch; motor issue. | Check power connection and circuit breaker. Ensure float switch is free to move. If issues persist, contact qualified service personnel. |
| Pump runs but does not pump water. | Clogged intake or discharge pipe; air lock; low water level. | Disconnect power and clear any obstructions from intake and discharge. Check for air lock and ensure sufficient water level for activation. |
| Pump runs continuously. | Stuck float switch; continuous water inflow; faulty check valve. | Disconnect power and check float switch for obstructions. Verify that water inflow is not constant. Inspect check valve for proper function. |
| Pump is noisy or vibrates excessively. | Debris in impeller; pump not stable; worn bearings. | Disconnect power and inspect impeller for debris. Ensure pump is on a stable surface. If bearings are worn, professional service may be required. |
7. Product Specifications
| Feature | Detail |
|---|---|
| Model Number | SP05002VD |
| Manufacturer | EVERBILT |
| Horsepower | 0.5 HP |
| Power Source | AC |
| Material | Cast Iron, Stainless Steel |
| Color | Stainless Steel/Black |
| Item Weight | 16.54 Pounds (7.5 kg) |
| Product Dimensions (L x W x H) | 7.24 x 8.74 x 12.2 inches (18.39 x 22.2 x 30.99 cm) |
| Switch Type | Innovative Reed Sensor Vertical Float Switch |
| Bearings | Permanent Lubricated Ball Bearings |
| ASIN | B00LMIHBHE |
8. Warranty and Support
Specific warranty details for the Everbilt 1/2 HP Submersible Sump Pump (Model SP05002VD) are not provided in this manual. For warranty information, technical support, or to inquire about replacement parts, please contact Everbilt customer service directly or refer to the official Everbilt website. Keep your purchase receipt as proof of purchase.
Manufacturer: EVERBILT
