Product Overview
Figure 1: Top-down view of the Electrolux 134711401 Thermal Fuse.
The Electrolux 134711401 Thermal Fuse is a genuine replacement part designed for Electrolux dryers. This component acts as a safety device, interrupting the electrical circuit to the dryer's heating element if the dryer overheats, preventing potential fire hazards. It is engineered to exact specifications to ensure optimal performance and safety of your appliance.
Figure 2: Angled view of the Electrolux 134711401 Thermal Fuse, showing its compact design and terminals.
Figure 3: The thermal fuse, a critical component for dryer safety and function.
A thermal fuse is a one-time use safety device. If it blows, it indicates an underlying issue causing the dryer to overheat, such as restricted airflow (clogged lint trap or vent), a faulty heating element, or a malfunctioning thermostat. Replacing the thermal fuse without addressing the root cause will likely result in the new fuse blowing again.
Compatibility
This genuine Electrolux 134711401 Thermal Fuse is compatible with a wide range of Electrolux dryer models. To ensure proper fit and function, always verify compatibility with your specific appliance model before purchasing and installation. Refer to your dryer's user manual or the appliance's model number for confirmation.
Figure 4: Example of compatible Electrolux dryer models. Always cross-reference with your specific model.
Some compatible Electrolux models include, but are not limited to: EDV114Z, EIED50L, EIGD50L, CARE1011, CASE7074, CDE4700L, CDE4701Q, CDE7300R, CDE7400Q, CDG4700L, CDG4701Q, CDG7300R, CDG7400Q, CDG7700L, EFDC317T, EFDE317T, EFDG317T, EFMC417S, EFMC427U, EFMC517S, EFMC527U, EFMC617S, EFMC627U, EFME417S, EFME427U, EFME517S, EFME527U, EFME617S, EFME627U, EFME628W, EFMG417S, EFMG427U, EFMG517S, EFMG527U, EFMG617S, EFMG627U, EFMG628W, EIGD50LI, EIMED5CQ, EIMED55I, EIMED55Q, EIMED6CJ, EIMED6CL, EIMED60J, EIMED60L, EIMGD55I, EIMGD55Q, EIMGD60J, EIMGD60L, EWMED7CJ, EWMED70J, EWMGD70J, FARE1011, FARG1011, FASG7074, ADE776NZH, CAQE7001L, CAQE7021L, CARE1011M, CARE4044M, CASE7021N, CASE7074N, CFQE4000Q, CFQE5000Q, CFQE5100P, CFRE1001P, CFSE5100Q, CFSE5115P, EIMED55II, EIMED6CJI, EIMED60JI, ELFE733CA, ELFE7337A, ELFE743CA, ELFE7437A, ELFE753CA, ELFE7537A, ELFE763CA, ELFE763CB, ELFE7637A, ELFE7637B, ELFG7337A, ELFG7437A, ELFG7537A, ELFG7637A, ELFG7637B, ELTE730CA, ELTE7300A, ELTE760CA, ELTE7600A, ELTG7300A, ELTG7600A, FAQE7111L, FAQG7001L, FAQG7111L, FARE1011M, FARE4044M, FARG1011M, FARG4044M, FASE7021N, FASE7073N, FASE7074N, FASG7021N, FASG7073N, FASG7074N, FDEX21E4E, FDEX22E4E, FDGX21E4E, FDGX22E4E, FFQE5000Q, FFQE5100P, FFQG5000Q, FFQG5100P, FFRE1001P, FFRG1001P, FFSE5115P, FFSG5115P, MDE675NZH, MDE676NZH, SFRG1011M.
Installation Information
Replacing a thermal fuse in a dryer requires careful attention to safety and proper procedures. It is recommended that this part be installed by an experienced repair person or someone with specialized training to ensure correct installation and to diagnose any underlying issues that caused the original fuse to blow.
Figure 4: Recommended skill level and tools for thermal fuse replacement.
Tools Required:
- Long #2 cross-head screwdriver
- Short #2 cross-head screwdriver
- Flat-blade screwdriver
- Wire cutters
- Zip ties
- Gloves
- Safety glasses
- Multimeter (for testing continuity)
General Installation Steps (Consult Service Manual for Specifics):
- Safety First: Always disconnect power to the dryer by unplugging it or turning off the circuit breaker before beginning any repair.
- Access the Thermal Fuse: Depending on your dryer model, you may need to remove the back panel, top panel, or front panel to access the thermal fuse.
- Locate the Thermal Fuse: The thermal fuse is typically located on the blower housing or near the heating element. It is a small, white, rectangular component with two wire terminals.
- Test the Old Fuse: Use a multimeter set to continuity mode to test the old thermal fuse. If it shows an open circuit (OL or no continuity), it is blown and needs replacement.
- Disconnect Wires: Carefully disconnect the wires from the old thermal fuse. Note their positions for correct reattachment.
- Remove Old Fuse: Unscrew or unclip the old thermal fuse from its mounting bracket.
- Install New Fuse: Secure the new Electrolux 134711401 Thermal Fuse in place and reattach the wires to the correct terminals.
- Reassemble Dryer: Reattach any panels removed during the process.
- Restore Power: Plug the dryer back in or turn on the circuit breaker.
- Test Dryer: Run a short cycle to ensure the dryer operates correctly and heats properly.
Figure 5: Close-up of the thermal fuse, showing the two terminals for electrical connection.
Operating Considerations
The thermal fuse operates automatically as a safety measure. There are no user-adjustable settings for this component. Its function is to protect the dryer from overheating. If the thermal fuse blows, the dryer will typically stop heating or may not start at all.
Maintenance
To prevent the thermal fuse from blowing and ensure the longevity of your dryer, regular maintenance is crucial:
- Clean Lint Filter: Clean the lint filter before every load. A clogged lint filter restricts airflow, causing the dryer to overheat.
- Inspect Dryer Vent: Periodically inspect and clean the entire dryer vent system (from the dryer to the outside exhaust). Lint buildup in the vent is a common cause of overheating and fire hazards.
- Avoid Overloading: Do not overload the dryer. Overloading can restrict airflow and cause the dryer to work harder, leading to overheating.
- Check for Proper Airflow: Ensure the dryer has adequate space around it for proper ventilation.
Troubleshooting
If your dryer is experiencing issues, especially after replacing a thermal fuse, consider the following troubleshooting steps:
- Dryer Not Heating: If the dryer runs but does not produce heat, the thermal fuse may have blown, or the heating element or operating thermostat could be faulty. Test all related components for continuity.
- Dryer Not Starting: A blown thermal fuse can prevent the dryer from starting. Other causes include a faulty door switch, start switch, or motor.
- Repeated Thermal Fuse Failure: If a newly installed thermal fuse blows quickly, it indicates an unresolved underlying issue. The most common causes are:
- Clogged Vent System: This is the most frequent cause. Thoroughly clean the entire exhaust duct.
- Faulty Cycling Thermostat: A thermostat that fails to open can allow the dryer to overheat.
- Faulty High-Limit Thermostat: If the high-limit thermostat fails, it won't prevent overheating, leading to the thermal fuse blowing.
- Malfunctioning Heating Element: A shorted or partially failed heating element can cause excessive heat.
- Unusual Noises: While not directly related to the thermal fuse, unusual noises can indicate other mechanical issues that might indirectly affect dryer operation and potentially lead to overheating if not addressed.
Always ensure the dryer's vent system is clear and unobstructed to maintain proper airflow and prevent overheating.
Specifications
| Brand Name | Electrolux |
| Model Number | 134711401 |
| Item Weight | 0.32 ounces |
| Product Dimensions | 0.5 x 0.5 x 0.5 inches |
| Part Number | 134711401 |
| Batteries Required? | No |
| Date First Available | July 1, 2014 |
Warranty and Support
For warranty information regarding the Electrolux 134711401 Thermal Fuse, please refer to the official Electrolux warranty policy provided with your appliance or visit the official Electrolux website. For technical support, installation assistance, or to inquire about service, please contact Electrolux customer service directly.
You can find contact information for Electrolux customer support on their official website or in your appliance's user manual.
