Introduction
This manual provides instructions for the proper installation and use of the LogiLink Professional NP0223 Surface Mounted Housing. This product is designed to convert a recessed connection can into a surface-mounted version, providing a clean and functional enclosure. The NP0223 is supplied in signal white (RAL9003) and is compatible with all LogiLink recessed connection cans and other standard UP cans.
Product Overview
The LogiLink Professional NP0223 is a surface-mounted frame designed to house recessed connection cans. Its robust construction ensures durability and a professional finish for your network or electrical installations.
Key Features:
- Surface-Mounted Frame with dimensions of 80 x 80 x 40 mm.
- Compatible with LogiLink recessed cans and all standard UP cans.
- Color: RAL9003 Signal White.
- Weight: Approximately 100g.
Figure 1: Front view of the LogiLink NP0223 Surface Mounted Housing, showing the central opening and mounting points.
Setup and Installation
Follow these steps to properly install your LogiLink Professional NP0223 Surface Mounted Housing.
Components Included:
Figure 2: Included accessories for installation, typically consisting of mounting screws and cable ties.
- Unpack Components: Carefully remove the surface-mounted housing and all accessories from the packaging. Verify that all components, including the housing, mounting screws, and cable ties, are present.
- Identify Mounting Location: Choose a suitable, flat surface for mounting the housing. Ensure there is sufficient space for the housing (80x80x40 mm) and any associated cabling.
- Prepare Mounting Holes: Hold the housing against the desired mounting surface and mark the positions for the mounting screws. Drill pilot holes if necessary, appropriate for the type of wall material.
- Secure Housing to Surface: Position the housing over the pilot holes and secure it to the surface using the provided mounting screws. Ensure the housing is firmly attached and level.
Figure 3: Side view illustrating the depth of the housing and potential cable entry points.
- Insert Recessed Connection Can: Carefully insert your LogiLink or standard recessed connection can into the surface-mounted housing. Align the mounting holes of the recessed can with the internal screw inserts of the surface housing.
Figure 4: Detail of the internal screw insert, where the recessed connection can will be secured.
- Secure Recessed Can: Use appropriate screws (often supplied with the recessed can itself, or small screws if provided with the housing) to secure the recessed can to the internal screw inserts of the surface housing. Do not overtighten.
- Cable Management: Route any necessary cables through the designated openings in the housing. Use the provided cable ties to manage and secure cables, ensuring a tidy and organized installation.
Operating
The LogiLink Professional NP0223 Surface Mounted Housing is a passive component. Once correctly installed, it provides a protective and aesthetic enclosure for your recessed connection can, allowing the integrated components (e.g., network jacks) to function as intended. No specific operational steps are required for the housing itself.
Maintenance
The LogiLink Professional NP0223 Surface Mounted Housing requires minimal maintenance.
- Cleaning: Periodically wipe the exterior of the housing with a soft, dry, or slightly damp cloth to remove dust and dirt. Avoid using abrasive cleaners or solvents, as these may damage the finish.
- Inspection: Occasionally inspect the housing for any signs of physical damage, loose screws, or discoloration. Address any issues promptly to maintain the integrity of the installation.
Troubleshooting
This section addresses common issues that may arise during the installation or use of the surface mounted housing.
- Housing Does Not Fit Recessed Can:
- Ensure your recessed connection can is compatible with the housing's dimensions (80 x 80 x 40 mm).
- Verify that the recessed can is a standard UP can or a LogiLink recessed can.
- Housing is Not Securely Mounted:
- Check that the mounting screws are appropriate for the wall material and are tightened sufficiently.
- Ensure the mounting surface is flat and stable.
- Cables Are Difficult to Route:
- Utilize the designated cable entry points on the housing.
- Consider pre-routing cables before fully securing the recessed can.
Specifications
| Model Number: | NP0223 |
| Brand: | LogiLink |
| Manufacturer: | 2direct GmbH |
| Product Dimensions (L x W x H): | 8 x 8 x 4 cm (80 x 80 x 40 mm) |
| Item Weight: | 100g |
| Color: | RAL9003 Signal White |
| Compatibility: | LogiLink recessed cans, standard UP cans |
Warranty and Support
For information regarding warranty coverage and technical support for your LogiLink Professional NP0223 Surface Mounted Housing, please refer to the documentation provided with your purchase or contact your retailer. You may also visit the official LogiLink website for further assistance.
