1. Product Overview
The Defiant 180 Degree Black Motion-Sensing Outdoor Security Light is designed to provide enhanced security and illumination for outdoor areas such as driveways and garages. This unit features advanced technology including DualBrite 2-Level Lighting, Alert Flash Security, and Bulb Life Extending Technology, ensuring efficient and reliable operation.
Key features include:
- DualBrite 2-Level Lighting: Offers accent lighting when no motion is present and full bright light for security when motion is detected.
- Selectable Motion Timer: Adjustable settings (test, 1, 5, 10 minutes) to optimize energy usage.
- Bulb Compatibility: Uses 2 - 120-Watt PAR 38-bulbs (not included), compatible with PAR38 incandescent and select PAR38 dimmable LED outdoor rated-wet rated bulbs.
- Durable Construction: Designed for long-lasting outdoor operation with light shields for bulb protection.
2. Safety Information
Please read and understand all instructions before beginning installation. Failure to follow these instructions may result in electric shock, fire, or other hazards that could cause injury or property damage.
- WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installing or servicing.
- WARNING: Risk of fire. Keep combustible materials away from the lamp.
- This fixture is intended for use with 120V/60Hz power supply.
- All wiring connections must be in accordance with local electrical codes.
- Do not install near flammable surfaces or materials.
- Ensure the fixture is securely mounted to a suitable surface.
- Do not look directly into the light source when illuminated.
3. Package Contents
Verify that all components are present before beginning installation:
- Defiant 180 Degree Motion-Sensing Outdoor Security Light
- Mounting Hardware (screws, wire nuts, gasket)
- Instruction Manual
Note: PAR38 bulbs are not included and must be purchased separately.
4. Specifications
| Specification | Detail |
|---|---|
| Model Number | DF-5416-BK |
| Power Source | Corded Electric |
| Voltage | 110 Volts |
| Bulb Type | PAR38 Incandescent or Dimmable LED (not included) |
| Max Wattage per Bulb | 120 Watts |
| Motion Sensor Range | 180 Degrees |
| Indoor/Outdoor Usage | Outdoor |
| Installation Type | Wall-mounted |
| Dimensions (L x W x H) | 8 x 14 x 12.5 inches |
| Item Weight | 1.75 Pounds |
| Water Resistance Level | Water Resistant |
5. Setup and Installation
Before starting, ensure the power to the installation area is turned OFF at the circuit breaker or fuse box.
5.1 Mounting the Fixture
The security light is designed for wall-mounted installation. Choose a location that provides optimal coverage for the motion sensor and light output.
- Carefully remove the mounting plate from the back of the fixture.
- Position the mounting plate over the junction box and mark the screw holes.
- Secure the mounting plate to the wall using the provided mounting hardware. Ensure it is firmly attached.
- Feed the electrical wires from the junction box through the center hole of the mounting plate.
Figure 5.1: Front view of the security light, showing the two lamp heads and the motion sensor unit.
Figure 5.2: Side view illustrating the adjustable arm and the mounting bracket for wall installation.
5.2 Wiring Connections
Connect the wires according to standard electrical practices. If you are unsure, consult a qualified electrician.
- Connect the black wire from the fixture to the black (hot) wire from the junction box using a wire nut.
- Connect the white wire from the fixture to the white (neutral) wire from the junction box using a wire nut.
- Connect the green or bare copper (ground) wire from the fixture to the ground wire from the junction box using a wire nut.
- Carefully tuck all wires into the junction box.
5.3 Attaching the Fixture Body and Installing Bulbs
- Align the fixture body with the mounting plate and secure it with the provided screws. Ensure the gasket is properly seated to prevent water intrusion.
- Screw two PAR38 bulbs (up to 120W each, not included) into the lamp holders. Do not overtighten.
6. Operating Instructions
Once installed and powered on, the security light can be configured for optimal performance.
6.1 Adjusting Lamp Heads and Sensor
The lamp heads and motion sensor are adjustable to direct light and detection where needed.
- Loosen the adjustment knobs on the lamp heads and sensor.
- Pivot the lamp heads to illuminate the desired area.
- Angle the motion sensor to cover the desired detection zone (up to 180 degrees).
- Tighten the adjustment knobs to secure their positions.
Figure 6.1: Detail of the motion sensor and its adjustable controls.
6.2 Setting the Motion Timer
The motion timer determines how long the light stays on after motion is detected and stops. The available settings are Test, 1, 5, and 10 minutes.
- Locate the "TIME" dial on the bottom of the motion sensor.
- Rotate the dial to select the desired duration:
- Test: For initial setup and aiming. Light stays on for a few seconds.
- 1 min: Light stays on for 1 minute after motion ceases.
- 5 min: Light stays on for 5 minutes after motion ceases.
- 10 min: Light stays on for 10 minutes after motion ceases.
6.3 DualBrite 2-Level Lighting
This feature provides a low-level accent light during darkness, which brightens to full intensity upon motion detection.
- Locate the "DUALBRITE" dial on the bottom of the motion sensor.
- Rotate the dial to activate or deactivate this feature, and to adjust the duration of the low-level accent light (if applicable, refer to specific product manual for detailed settings).
- When activated, the light will illuminate at a low level from dusk to dawn, and switch to full brightness when motion is detected.
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your security light.
- Cleaning: Periodically clean the fixture with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure the motion sensor lens is clear of dirt and debris for proper operation.
- Bulb Replacement:
- Turn off power to the fixture at the circuit breaker.
- Allow bulbs to cool completely before handling.
- Unscrew the old PAR38 bulb and screw in a new one (up to 120W).
- Restore power and test.
- Inspections: Annually inspect wiring connections and mounting hardware for any signs of wear, corrosion, or loosening.
8. Troubleshooting
If your security light is not functioning as expected, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on at all. | No power; faulty bulb; wiring issue. | Check circuit breaker/fuse. Replace bulbs. Verify wiring connections. |
| Light stays on continuously. | Sensor in "Test" mode; constant motion detected; wiring error. | Adjust "TIME" dial off "Test". Clear obstructions from sensor view. Recheck wiring. |
| Light turns on during the day. | Photocell blocked or faulty. | Ensure photocell (small clear dome on sensor) is not obstructed by dirt or objects. |
| Motion sensor not detecting. | Sensor obstructed; incorrect angle; sensitivity too low. | Clean sensor lens. Adjust sensor angle. Increase sensitivity (if applicable, refer to product specific controls). |
9. Warranty and Support
This Defiant product is backed by a manufacturer's warranty. For specific warranty details, including duration and coverage, please refer to the warranty card included with your purchase or visit the official Defiant website.
For technical support, replacement parts, or further assistance, please contact Defiant customer service. Contact information can typically be found on the product packaging or the manufacturer's website.
Online Resources: For additional information, FAQs, or video tutorials, please visit the official Defiant support page. Defiant Lighting Products
