Introduction
This manual provides essential instructions for the safe and effective installation, operation, and maintenance of your Electrolux Original Floor Polisher Wide Belt (30mm Width), model 102335007. This replacement belt is designed to restore the functionality of your floor polisher if the polishing pads are no longer rotating due to a worn or broken belt.
Figure 1: Electrolux Original Floor Polisher Wide Belt (Model 102335007). This image shows the replacement belt, which is 30mm wide and designed for specific Electrolux floor polisher models.
Setup and Installation
Before attempting any installation, ensure your floor polisher is unplugged from the power source to prevent electric shock or injury. Refer to your floor polisher's original user manual for specific disassembly instructions.
- Safety First: Disconnect the floor polisher from the main power supply.
- Access the Belt Mechanism: Carefully open the floor polisher's casing to access the drive belt mechanism. This usually involves removing screws or latches. Consult your polisher's manual for precise steps.
- Remove Old Belt: Locate the old, worn, or broken belt. Gently remove it from the motor shaft and the polishing pad assembly. Note its orientation for correct installation of the new belt.
- Install New Belt: Position the new Electrolux belt (Model 102335007) onto the motor shaft and then stretch it over the polishing pad assembly. Ensure the belt is seated correctly in all grooves and pulleys. The belt dimensions are 720mm (length) x 30mm (width) x 3mm (thickness).
- Verify Tension: Once installed, the belt should be taut but not overly tight, allowing for smooth rotation without excessive strain on the motor.
- Reassemble: Carefully reassemble the floor polisher casing, ensuring all screws and latches are securely fastened.
- Initial Test: Plug the floor polisher back into the power supply and perform a brief test run to ensure the polishing pads rotate correctly and smoothly.
Operating Instructions
This product is a replacement drive belt and does not have independent operating controls. Its function is to transmit power from the motor to the polishing pads of your compatible Electrolux floor polisher. Once correctly installed, the floor polisher should operate as intended by its original design.
- Always refer to your specific floor polisher's user manual for detailed operating instructions, safety guidelines, and recommended usage.
- Ensure the belt is free from obstructions and properly seated before each use.
- If you notice any unusual noises, vibrations, or a decrease in polishing performance after belt replacement, immediately turn off and unplug the polisher and inspect the belt installation.
Maintenance
Proper maintenance can extend the life of your drive belt and ensure optimal performance of your floor polisher.
- Regular Inspection: Periodically inspect the belt for signs of wear, cracking, fraying, or stretching. Replace the belt if any damage is observed.
- Cleanliness: Keep the belt and surrounding mechanism free from dust, debris, and polishing compounds, which can cause premature wear.
- Storage: When not in use, store the floor polisher in a clean, dry environment away from extreme temperatures or direct sunlight, which can degrade belt materials.
- Avoid Overloading: Do not apply excessive pressure to the floor polisher during operation, as this can put undue strain on the drive belt and motor.
Troubleshooting
If you encounter issues after installing the new drive belt, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Polishing pads do not rotate or rotate slowly. | Belt not properly seated; incorrect belt size; motor issue; new belt is faulty. |
|
| Unusual noise or vibration during operation. | Belt misalignment; foreign object in mechanism; worn bearings in polisher. |
|
| Belt breaks shortly after replacement. | Improper installation (over-tensioned); manufacturing defect; underlying issue with polisher mechanism. |
|
Product Specifications
| Brand | Electrolux |
| Model Number | 102335007 |
| Product Reference | 102335007 |
| Product Dimensions (L x W x H) | 72 x 3 x 0.3 cm (720 x 30 x 3 mm) |
| Weight | 80 grams |
| Size | One size (72cm length) |
| Number of items in package | 1 |
| Belt Style | Flat belt |
| Compatible Devices | Floor Polisher models B9, B19, B21, B22, B23, TYPE 2D, 3D, 5G, 6G |
| Manufacturer | ELECTROLUX |
| ASIN | B00KMVPH4Q |
| International Article Code | 05054127779863 |
Warranty and Support
This product is a replacement part. Specific warranty information for replacement parts may vary. Please retain your proof of purchase.
- For warranty claims or technical assistance, please contact your original retailer or visit the official Electrolux website for customer support information in your region.
- Availability of spare parts information is not provided in the product details.
For further assistance, please refer to the contact information provided with your original floor polisher or on the official Electrolux support channels.
