Kirby 32-Foot Electric Power Cord Instruction Manual

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of your Kirby 32-Foot Electric Power Cord. This genuine Kirby power cord is designed to provide reliable power to your vacuum cleaner, ensuring optimal performance and extended reach for cleaning tasks.

Image: The Kirby 32-Foot Electric Power Cord, coiled for storage.

2. Compatibility

This power cord is compatible with the following Kirby vacuum cleaner models:

• Diamond Edition (DE) G8, G8D
• Ultimate G (ULTG) G7, G7D
• Generation 3 (G3)
• Gsix (G6) G6D G2000 Limited Edition G2001
• G5, G5D
• G4, G4D

This cord is a direct replacement for Kirby Part #192001.

3. Product Features

• Length: 32 feet for extended reach.
• Voltage: 120 Volt operation.
• Prongs: 2-prong design.
• Color: Black.
• Construction: Made of high-quality rubber and copper for durability and corrosion resistance.
• Connection: Male-to-Female connector gender, Type A plug format.

Image: Close-up of the power cord's durable construction.

Image: Detail showing corrosion-resistant features of the cord.

4. Installation Instructions

Replacing the power cord on your Kirby vacuum cleaner is a straightforward process. Follow these steps carefully:

4.1. Tools Required

• Two Torx bit drivers (different sizes may be needed)
• Flat blade screwdriver

4.2. Step-by-Step Installation

1. Disconnect Power: Ensure the vacuum cleaner is unplugged from the wall outlet before beginning any maintenance.
2. Remove Bag Housing: Remove the bag housing from the sweeper. This is typically done by twisting the grey plastic 90-degree piece at the bottom of the bag counter-clockwise until it comes loose, then lifting it off.
3. Access Cord Connection: Use a Torx driver to remove the screw from the plastic cover located over the end of the cord connection on the vacuum. You may need a flat blade screwdriver to gently slide this cover towards the top of the sweeper to remove it.
4. Unplug Old Cord: Once the cover is removed, unplug the old power cord from its connection point.
5. Remove Cord Keeper Screw: On the back of the sweeper, near the power switch, locate the screw that holds the cord keeper in place under a plastic cover. Remove this screw.
6. Remove Old Cord Keeper: Lift up on the cover to remove the old cord keeper.
7. Insert New Cord Keeper: Insert the new cord keeper under the cover.
8. Secure New Cord Keeper: Reset the cover and re-insert the screw to secure the new cord keeper.
9. Route New Cord: Unlace the old cord from the handle and route the new cord into its place, ensuring it is properly secured along the handle.
10. Connect New Cord: Replace the cover over the plug on the side of the sweeper and plug in the new power cord.
11. Reattach Bag Housing: Reattach the bag to the sweeper by starting with it at approximately a 45-degree angle, pressing it down onto the connection, and rotating it clockwise until it locks in place.

4.3. Installation Video Guide

For a visual guide on replacing the power cord, please refer to the video below. This video demonstrates the steps involved in replacing a Kirby vacuum cleaner power cord.

Another helpful video for general power cord replacement:

5. Operating Instructions

Once the new power cord is securely installed, operating your Kirby vacuum cleaner is simple:

1. Plug In: Insert the 2-prong plug of the power cord into a standard 120V AC wall outlet.
2. Power On: Turn on your Kirby vacuum cleaner using its power switch.
3. Extended Reach: Utilize the 32-foot length of the cord to reach various areas without frequently changing outlets.
4. Unplug Safely: When finished, turn off the vacuum cleaner and unplug the cord by grasping the plug, not the cord itself.

6. Maintenance and Care

Proper care of your power cord will ensure its longevity and safe operation:

• Avoid Kinks and Twists: Do not excessively bend, kink, or twist the power cord, as this can damage the internal wiring.
• Store Properly: When not in use, coil the cord neatly around the designated cord wraps on your vacuum cleaner.
• Inspect Regularly: Periodically inspect the cord for any signs of damage, such as cuts, fraying, or exposed wires. If damage is found, replace the cord immediately.
• Keep Dry: Avoid exposing the power cord to water or excessive moisture.

7. Troubleshooting

If your Kirby vacuum cleaner is not receiving power after installing the new cord, consider the following:

• Check Connections: Ensure both ends of the power cord are securely plugged into the vacuum and the wall outlet.
• Verify Outlet: Test the wall outlet with another appliance to confirm it is functioning correctly.
• Inspect Cord: Double-check the entire length of the power cord for any visible damage.
• Internal Wiring: If the issue persists, there might be an internal wiring problem with the vacuum cleaner itself, which may require professional service.

8. Specifications

9. Warranty and Support

For information regarding warranty coverage or technical support for your Kirby power cord, please refer to the official Kirby website or contact Kirby customer service directly. Keep your purchase receipt as proof of purchase.