1. Introduction
Thank you for choosing the ALFA 10B 10-Quart Replacement Beater Paddle. This high-quality attachment is designed to provide efficient and consistent mixing results in commercial kitchen environments. It serves as a direct replacement for the Hobart 275455 beater paddle and is compatible with Hobart C100 mixers.
This manual provides essential information for the proper installation, safe operation, and effective maintenance of your ALFA 10B beater paddle to ensure its longevity and optimal performance.
2. Safety Information
Always prioritize safety when operating commercial kitchen equipment. Please observe the following precautions:
- Read Your Mixer Manual: Always refer to your Hobart C100 mixer's instruction manual for specific safety guidelines and operating procedures.
- Power Off Before Installation/Removal: Ensure the mixer is turned off and unplugged from the power source before installing, removing, or cleaning the beater paddle.
- Secure Attachment: Verify that the beater paddle is securely attached to the mixer shaft before operation.
- Keep Hands Clear: Never place hands or utensils into the mixing bowl while the mixer is operating.
- Supervision: Do not allow untrained personnel to operate the mixer with the attachment.
3. Setup and Installation
Follow these steps to properly install the ALFA 10B beater paddle onto your Hobart C100 mixer:
- Prepare the Mixer: Ensure the mixer is turned off and unplugged. Lower the mixing bowl if applicable.
- Attach the Paddle: Align the top of the ALFA 10B beater paddle with the mixer's attachment shaft. Push the paddle upwards onto the shaft and rotate it until the pin on the shaft engages with the groove on the paddle.
- Secure the Paddle: Gently pull down on the paddle to ensure it is firmly locked into place. It should not wobble or detach easily.
- Position the Bowl: Raise and secure the mixing bowl into its operating position.
Figure 1: The ALFA 10B 10-Quart Replacement Beater Paddle. This image shows the full view of the metal beater paddle, ready for installation into a commercial mixer.
4. Operating Instructions
The ALFA 10B beater paddle is designed for general mixing tasks, including batters, icings, mashed potatoes, and light doughs. For optimal results, consider the following:
- Load Capacity: Do not exceed the recommended capacity of your Hobart C100 mixer. Overloading can strain the mixer and the paddle.
- Speed Control: Utilize your mixer's adjustable speed control. Start at a low speed to incorporate ingredients, then gradually increase as needed for thorough mixing. Avoid high speeds with very thick mixtures to prevent undue stress on the equipment.
- Scraping: Periodically stop the mixer and scrape down the sides of the bowl to ensure all ingredients are fully incorporated.
Figure 2: The ALFA 10B beater paddle resting on a kitchen counter, illustrating its robust design and readiness for use in a commercial setting.
5. Maintenance and Cleaning
Proper cleaning and maintenance will extend the life of your ALFA 10B beater paddle:
- Immediate Cleaning: Clean the paddle immediately after each use to prevent food residue from drying and hardening.
- Dishwasher Safe: The ALFA 10B beater paddle is dishwasher safe. For best results, place it on the top rack or ensure it is not obstructed by other items.
- Hand Washing: If hand washing, use warm, soapy water and a non-abrasive sponge or brush. Rinse thoroughly and dry completely to prevent water spots or mineral buildup.
- Inspection: Periodically inspect the paddle for any signs of wear, damage, or bending. Replace if any significant damage is observed to maintain optimal mixing performance and safety.
Figure 3: A top-down view of the ALFA 10B beater paddle, highlighting its structural details for thorough cleaning and inspection.
6. Troubleshooting
If you encounter issues with your ALFA 10B beater paddle, consider the following:
- Paddle Not Attaching Securely:
- Ensure the mixer is off and unplugged.
- Verify that the attachment shaft is clean and free of debris.
- Confirm the paddle is correctly aligned with the pin and groove on the shaft.
- Inconsistent Mixing:
- Check if the paddle is bent or damaged. A damaged paddle may not scrape the bowl effectively.
- Ensure the bowl is properly seated and at the correct height for the paddle to reach all ingredients.
- Adjust mixing speed and duration according to the recipe and ingredient consistency.
- Unusual Noise During Operation:
- Immediately turn off the mixer.
- Inspect the paddle for any damage or foreign objects.
- Ensure the paddle is not hitting the sides or bottom of the mixing bowl. Adjust bowl height if necessary (refer to your mixer's manual).
7. Specifications
| Brand | ALFA |
| Model Name | 10B |
| Capacity | 10-Quart Mixers |
| Compatibility | Replaces Hobart 275455, Compatible with Hobart C100 Mixers |
| Material | High-Quality Metal Construction |
| Dishwasher Safe | Yes |
| Item Weight | 1 pound |
8. Warranty Information
ALFA International stands behind the quality of its products. The ALFA 10B beater paddle comes with an industry-leading warranty, ensuring that it meets or exceeds original equipment manufacturer (OEM) specifications. For specific warranty terms and conditions, please refer to the official ALFA International website or contact customer support.
9. Support
For further assistance, technical support, or inquiries regarding your ALFA 10B beater paddle, please contact ALFA International. As a family-owned and USA-based company since 1938, ALFA is committed to customer satisfaction and providing reliable foodservice equipment and replacement parts.
Please visit the official ALFA International website for contact details and additional resources.
