ES 485

Download PDF
Contents

Electronic Specialties 485 Self Calibrating True RMS Digital Multimeter Instruction Manual

Model: 485 | Brand: ES

1. Introduction

This manual provides detailed instructions for the safe and effective use of your Electronic Specialties 485 Self Calibrating True RMS Digital Multimeter (DMM). This full-function DMM is designed for professional technicians, offering precise measurements and a patented self-calibration function.

Key features include:

  • Full function True RMS DMM designed for the professional technician
  • Patented self-calibration function
  • Measures Volts, Ohms, Amps, Frequency, Capacitance, Duty Cycle, Diodes, Continuity and Temperature
  • 6,000 count backlit LCD, MIN/MAX function, CATIII 600 volts safety rated
  • Includes 40-inch test leads, temperature probe, and zippered carrying case
Electronic Specialties 485 Digital Multimeter front view
Figure 1: Front view of the Electronic Specialties 485 Digital Multimeter. The device features a large digital display, a rotary selector dial for various measurement functions, and several control buttons.

2. Setup

2.1. Battery Installation

The ES 485 DMM requires one 9V battery for operation. To install the battery:

  1. Ensure the multimeter is powered off.
  2. Locate the battery compartment cover on the back of the device.
  3. Use a screwdriver to remove the screw securing the battery cover.
  4. Carefully remove the cover.
  5. Insert a new 9V battery, observing the correct polarity (+/-).
  6. Replace the battery cover and secure it with the screw.

2.2. Test Lead Installation

For most voltage, resistance, and continuity measurements, connect the test leads as follows:

  • Insert the black test lead into the COM (common) input jack.
  • Insert the red test lead into the VΩHzT input jack.

For current measurements (Amps, Milliamps, Microamps), refer to the Operating Instructions section for specific lead placement.

2.3. Temperature Probe Installation

To use the temperature measurement function:

  • Ensure the multimeter is powered off.
  • Insert the temperature probe's black connector into the COM input jack.
  • Insert the temperature probe's red connector into the VΩHzT input jack.
  • Select the temperature function on the rotary dial.
Electronic Specialties 485 Digital Multimeter with included accessories
Figure 2: The ES 485 DMM shown with its accessories, including test leads, temperature probe, and carrying case.

3. Operating Instructions

3.1. General Operation

The ES 485 DMM features a rotary dial to select measurement functions and buttons for additional settings. The device defaults to auto-ranging for most functions, providing optimal accuracy.

3.2. Voltage Measurement (AC/DC)

To measure voltage:

  1. Turn the rotary dial to the 'V~' (AC Voltage) or 'V=' (DC Voltage) position. The meter will default to DC.
  2. To switch between AC and DC voltage, press the SELECT button.
  3. Connect the test leads in parallel to the circuit or component you wish to measure.
  4. Read the voltage value on the backlit LCD display.

3.3. Resistance, Continuity, Diode, and Capacitance Measurement

To measure resistance (Ω), check continuity (audible beep), test diodes, or measure capacitance (∔):

  1. Turn the rotary dial to the 'Ω/∔/→|/)))' position.
  2. Press the SELECT button to cycle through the different functions (Resistance, Continuity, Diode, Capacitance).
  3. Connect the test leads to the component. For continuity, a beep indicates a continuous circuit.

3.4. Current Measurement (Amps, Milliamps, Microamps)

To measure current:

  1. Important: For current measurements, the circuit must be broken, and the multimeter must be connected in series.
  2. For measurements up to 600mA, insert the red test lead into the 'μA/mA' input jack. For measurements up to 10A, insert the red test lead into the '10A' input jack. The black lead remains in COM.
  3. Turn the rotary dial to the appropriate current range ('μA~', 'mA~', 'A~' for AC; 'μA=', 'mA=', 'A=' for DC).
  4. Press the SELECT button to switch between AC and DC current if needed.
  5. Connect the multimeter in series with the circuit.

3.5. Frequency (Hz) and Duty Cycle (%)

To measure frequency or duty cycle:

  1. Turn the rotary dial to the 'Hz' position.
  2. Connect the test leads to the signal source.
  3. Press the Hz/DUTY button to toggle between frequency and duty cycle readings.

3.6. Temperature Measurement

With the temperature probe installed (as per Section 2.3):

  1. Turn the rotary dial to the 'TEMP' position.
  2. The display will show the temperature. Use the SELECT button to switch between Celsius and Fahrenheit.

3.7. Self-Calibration Function

The ES 485 features a patented self-calibration function. Refer to the included training DVD or the detailed manual for specific instructions on performing a self-calibration.

3.8. MIN/MAX Function

Press the MAX/MIN button to capture the minimum and maximum readings during a measurement session. Press again to cycle through MAX, MIN, and current readings.

3.9. Backlit LCD

Press the backlight button (light bulb icon) to illuminate the display for improved visibility in low-light conditions.

3.10. Non-Contact Voltage (NCV) Detection

The ES 485 includes a non-contact voltage detection feature for quick identification of live AC voltage without direct contact. This feature is typically activated by a dedicated button or a specific rotary dial position (often labeled NCV).

Video: Detailed overview of the Electronic Specialties 485 Self Calibrating True RMS Digital Multimeter, demonstrating its various functions and features.

4. Maintenance

To ensure the longevity and accuracy of your ES 485 DMM:

  • Cleaning: Wipe the meter with a damp cloth and mild detergent. Do not use abrasives or solvents.
  • Battery Replacement: Replace the 9V battery when the low battery indicator appears on the display. Refer to Section 2.1 for installation steps.
  • Fuse Replacement: If the meter fails to measure current, the fuse may need replacement. Consult a qualified professional for fuse replacement to ensure safety and proper function.

5. Troubleshooting

Understanding common multimeter readings can help diagnose circuit issues:

5.1. Ghost Voltage

Ghost voltage occurs when a multimeter displays a voltage reading on an unpowered circuit. This is normal and typically indicates an open circuit. The meter is not defective.

5.2. Open Circuit

An open circuit is a break in the electrical path. When measuring voltage in an open circuit, the multimeter may show ghost voltage or no reading if the circuit is truly open. If you see ghost voltage, it's an immediate indication of an open circuit.

5.3. Short to Ground

A short to ground occurs when a live conductor makes unintentional contact with a grounded surface. When measuring voltage in a circuit with a short to ground, the multimeter will typically display true zero voltage (0.000V).

5.4. Overload (OL) / Out of Range

If the display shows

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.