1. Introduction
The Antari HC-1 Timer Remote is a dedicated accessory designed to provide enhanced control over compatible Antari haze machines. This remote allows users to precisely manage haze output duration and interval, as well as offering manual ON/OFF functionality. Its robust design and generous cable length ensure flexible placement and reliable operation in various professional settings.
2. Safety Information
- Always ensure the haze machine is powered off before connecting or disconnecting the HC-1 remote.
- Do not expose the remote to moisture or extreme temperatures.
- Avoid placing heavy objects on the cable to prevent damage.
- Use only with specified Antari haze machine models (HZ-100, HZ-300, HZ-400).
- If the remote appears damaged, discontinue use immediately and contact Antari support.
3. Package Contents
- 1 x Antari HC-1 Timer Remote Control with attached 25 ft. cable.
4. Product Overview

Figure 4.1: Antari HC-1 Timer Remote Control. The remote features two rotary knobs labeled 'DURATION' and 'INTERVAL' at the top, and three push buttons at the bottom. From left to right, these buttons are 'TIMER ON/OFF' (yellow), 'PUMP ON/OFF' (red), and 'HAZE' (teal). The unit is connected via a 1/4-inch stereo jack cable.
Controls and Indicators:
- DURATION Knob: Adjusts the length of time the haze machine will output haze during each cycle.
- INTERVAL Knob: Adjusts the time between each haze output cycle.
- TIMER ON/OFF Button (Yellow): Activates or deactivates the timer function.
- PUMP ON/OFF Button (Red): Manually controls the haze pump, allowing for continuous or momentary haze output.
- HAZE Button (Teal): Likely a manual override or burst button for immediate haze output.
- LED Indicators: Small indicator lights are present near the knobs and buttons to show status (e.g., power, timer active, haze output).
5. Setup
- Ensure your Antari haze machine (HZ-100, HZ-300, or HZ-400) is powered off and unplugged from the main power supply.
- Locate the remote control input jack on your haze machine. This is typically a 1/4-inch stereo jack.
- Insert the 1/4-inch stereo connector of the HC-1 remote cable firmly into the haze machine's remote input jack.
- Once connected, you may plug in and power on your haze machine. The remote is now ready for operation.
6. Operating Instructions
6.1. Timer Operation
- Set Duration: Rotate the 'DURATION' knob to set the desired length of each haze burst.
- Set Interval: Rotate the 'INTERVAL' knob to set the desired time between each haze burst.
- Activate Timer: Press the yellow 'TIMER ON/OFF' button. The corresponding LED indicator should illuminate, indicating that the timer function is active and the machine will now operate according to your set duration and interval.
- Deactivate Timer: Press the yellow 'TIMER ON/OFF' button again to stop the automatic timer operation.
6.2. Manual Operation
- Manual Haze Output: Press and hold the red 'PUMP ON/OFF' button for continuous haze output. Release the button to stop.
- Instant Haze: Press the teal 'HAZE' button for a momentary burst of haze.
7. Maintenance
- Keep the remote clean by wiping it with a soft, dry cloth. Do not use liquid cleaners or solvents.
- Regularly inspect the cable and connector for any signs of wear or damage. If damage is found, replace the remote.
- Store the remote in a cool, dry place when not in use.
8. Troubleshooting
- Remote not responding:
- Ensure the remote's 1/4-inch stereo connector is fully inserted into the haze machine's remote input.
- Verify that the haze machine is powered on and has warmed up sufficiently.
- Check the cable for any visible damage.
- Timer function not working:
- Ensure the yellow 'TIMER ON/OFF' button has been pressed and its indicator light is on.
- Adjust the 'DURATION' and 'INTERVAL' knobs to ensure they are not set to minimum or maximum values that might prevent noticeable output.
- No haze output:
- Confirm the haze machine has sufficient fluid.
- Check the haze machine's own power and readiness indicators.
9. Specifications
| Feature | Detail |
|---|---|
| Model | HC-1 |
| Compatible Haze Machines | Antari HZ-100, HZ-300, HZ-400 |
| Cable Length | 25 feet (approx. 7.6 meters) |
| Connector Type | 1/4 inch Stereo Jack |
| Functions | Timer with Interval and Duration, Manual ON/OFF |
| Controller Type | Button Control, Rotary Knobs |
| Item Weight | 2 pounds (approx. 0.91 kg) |
10. Warranty and Support
For warranty information and technical support, please refer to the documentation provided with your Antari haze machine or visit the official Antari website. Keep your purchase receipt as proof of purchase for any warranty claims.
For further assistance, please contact Antari customer service directly.