1. Introduction
Thank you for choosing the Awenta Ø 100mm Silent Bathroom Fan. This fan is designed for efficient and quiet air extraction in bathrooms, kitchens, and other utility rooms. Its robust construction and low noise level ensure a comfortable environment. Please read this manual carefully before installation and operation to ensure safe and correct use of the product.
2. Safety Instructions
- Always disconnect the power supply before installation, maintenance, or cleaning.
- Installation must be performed by a qualified electrician in accordance with local wiring regulations and standards.
- Ensure the voltage and frequency of the power supply match the specifications of the fan (230V, 50/60Hz).
- Do not operate the fan with a damaged power cord or plug.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Ensure proper ventilation in the room to prevent backflow of gases from open-flame appliances.
- The fan is designed for indoor use only and must not be exposed to direct water spray or extreme weather conditions. It is water-resistant and waterproof for typical bathroom environments.
3. Package Contents
Please check the package for the following items:
- Awenta Ø 100mm Bathroom Fan Unit
- Mounting Screws and Wall Plugs
- Instruction Manual (this document)
4. Installation
The Awenta Ø 100mm fan is suitable for both wall and ceiling mounting. Follow these steps for proper installation:
4.1 Pre-installation Checks
- Ensure the installation location has a Ø 100mm duct opening.
- Verify that the power supply is disconnected at the main circuit breaker.
- Confirm that the chosen location allows for adequate airflow and maintenance access.
4.2 Mounting the Fan
The fan can be mounted directly into a Ø 100mm ventilation duct. The unit is designed for secure attachment to a wall or ceiling surface.
Figure 1: Rear view of the fan, illustrating the duct connection and mounting points.
- Mark the positions for the mounting screws on the wall or ceiling using the fan's base as a template.
- Drill holes at the marked positions and insert the provided wall plugs.
- Insert the fan's duct connector into the ventilation duct.
- Secure the fan to the wall or ceiling using the provided screws. Ensure it is firmly attached.
4.3 Electrical Connection
The fan operates on 230V, 50/60Hz. Connect the fan to the electrical supply according to the wiring diagram provided inside the fan's terminal box. Ensure all connections are secure and insulated.
Figure 2: Front view of the Awenta Ø 100mm fan, showing the grille and brand logo.
5. Operation
Once installed and connected to the power supply, the fan can be operated via an external switch (e.g., a light switch in the bathroom). When the power is supplied, the fan will activate, extracting air from the room. The fan is designed for quiet operation, with a noise level of approximately 26 dBA.
Figure 3: Detailed view of the fan's grille and central mechanism.
6. Maintenance
Regular cleaning ensures optimal performance and longevity of your Awenta fan.
- Disconnect Power: Always ensure the power supply to the fan is disconnected before any cleaning or maintenance.
- Clean the Grille: The front grille can be gently wiped with a damp cloth to remove dust and dirt. Avoid using abrasive cleaners or solvents.
- Clean the Impeller: If necessary, carefully remove the front cover (if detachable) and gently clean the fan impeller blades with a soft brush or cloth. Be careful not to bend or damage the blades.
- Reassemble: After cleaning, ensure all parts are dry and securely reassembled before restoring power.
7. Troubleshooting
If you encounter issues with your fan, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Fan does not turn on | No power supply; loose wiring; faulty switch | Check circuit breaker; verify wiring connections; test the switch. Consult a qualified electrician if unsure. |
| Fan is unusually noisy | Obstruction in the duct or fan blades; loose mounting; worn bearings | Disconnect power and check for obstructions; ensure fan is securely mounted. If noise persists, contact support. |
| Low air extraction | Blocked duct; dirty fan blades; incorrect installation | Check duct for blockages; clean fan blades; review installation steps. |
If the problem persists after attempting these solutions, please contact your retailer or a qualified service technician.
8. Specifications
Figure 4: Approximate dimensions of the Awenta Ø 100mm fan.
| Feature | Specification |
|---|---|
| Brand | Awenta |
| Model | WZ100 (Armar Trading LTD) |
| Diameter | 100 mm |
| Airflow Capacity | 102 m³/h |
| Voltage | 230 V |
| Frequency | 50/60 Hz |
| Power Consumption | 4 Watts |
| Noise Level | 26 Decibels (dBA) |
| Bearing Type | Ball bearing (for continuous operation) |
| Material | Plastic |
| Color | White |
| Dimensions (L x W x H) | 8.5 x 15.9 x 17.9 cm (Product); 9.6P x 13.7W x 13.5H cm (Fan Design) |
| Weight | 480 g |
| Special Features | Water-resistant, Waterproof |
| Mounting Type | Wall Mount (also suitable for ceiling) |
9. Warranty and Support
For warranty information, please refer to the terms and conditions provided by your retailer at the time of purchase. Keep your proof of purchase for any warranty claims.
If you require technical assistance or have questions not covered in this manual, please contact the retailer or the manufacturer's customer support. Details can typically be found on the product packaging or the retailer's website.
