Introduction
This manual provides instructions for the installation, operation, and maintenance of your Remer 905CC2-CR Click Clack Pop-Up Waste. Please read this manual thoroughly before installation and retain it for future reference.
Image: The Remer 905CC2-CR Click Clack Pop-Up Waste, featuring a chrome finish and a contemporary round design. This image displays the main components of the pop-up waste, including the top stopper, threaded body, and lower drain section, along with sealing washers.
Safety Information
Observe the following safety guidelines during installation and use:
- Always turn off the water supply before beginning any plumbing work.
- Wear appropriate personal protective equipment, such as gloves and eye protection.
- If you are unsure about any step, consult a qualified plumber.
- Ensure all connections are watertight to prevent leaks.
Package Contents
The Remer 905CC2-CR Click Clack Pop-Up Waste includes the following components:
- Chrome Pop-Up Waste Assembly
- Sealing Washers
- Mounting Nut
Setup and Installation
This section outlines the general steps for installing the Remer 905CC2-CR Click Clack Pop-Up Waste. Specific installation requirements may vary based on your sink and plumbing configuration.
- Preparation: Ensure the sink drain opening is clean and free of debris.
- Positioning: Insert the upper part of the pop-up waste into the sink drain opening from above, ensuring the top sealing washer is correctly seated.
- Lower Assembly: From underneath the sink, slide the lower sealing washer and then the mounting nut onto the threaded body of the pop-up waste.
- Tightening: Hand-tighten the mounting nut, then use a wrench to gently tighten it further until secure. Avoid over-tightening, which can damage the seals or sink.
- Connect to Trap: Connect the tailpiece of the pop-up waste to your P-trap or S-trap assembly. Ensure all connections are sealed properly.
- Test for Leaks: Turn on the water supply and fill the sink. Check for any leaks around the drain assembly and connections.
Note: Some users have reported that adapting this Italian-made waste to US plumbing standards may require modifications to the tailpipe or an adapter. Consult a plumber if you encounter difficulties.
Operation
The Remer 905CC2-CR features a "Click Clack" mechanism for opening and closing the drain.
- To Close the Drain: Press down firmly on the chrome stopper. It will click into the closed position, sealing the drain.
- To Open the Drain: Press down firmly on the chrome stopper again. It will click into the open position, allowing water to drain.
Maintenance
Regular cleaning and maintenance will ensure the longevity and proper function of your pop-up waste.
- Cleaning: Clean the chrome finish regularly with a soft cloth and mild, non-abrasive cleaner. Avoid harsh chemicals or abrasive pads, which can damage the finish.
- Stopper Removal (for cleaning): The stopper can typically be unscrewed or pulled out for cleaning hair and debris from the drain opening. Refer to the specific design for removal.
- Seal Inspection: Periodically inspect the rubber seals for wear or damage. Replace if necessary to prevent leaks.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leaks around the drain. | Improperly seated seals or loose mounting nut. | Ensure seals are correctly positioned and the mounting nut is tightened securely. Do not overtighten. |
| Drain does not open or close properly. | Debris obstructing the click-clack mechanism or worn mechanism. | Remove the stopper and clean any debris. If the mechanism is worn, replacement may be necessary. |
| Slow drainage. | Hair or debris accumulation in the drain or P-trap. | Remove the stopper and clear any blockages. Clean the P-trap if necessary. |
Specifications
- Model: Remer 905CC2-CR
- Material: Brass
- Finish: Chrome
- Style: Contemporary Round Pop-Up Waste
- Dimensions: Approximately 1" L x 2.6" W x 3.61" H
- Item Weight: 1 pound
- Country of Origin: Italy
Warranty Information
For specific warranty details, please refer to the documentation provided with your purchase or contact Remer customer support.
Customer Support
For further assistance or inquiries, please contact your retailer or the manufacturer, Remer.
