Introduction
This manual provides instructions for the proper installation, operation, and maintenance of the Jones Stephens Corp Service Sink Hose with Stainless Bracket, Model M05001. Please read these instructions carefully before use to ensure safe and efficient operation.
Figure 1: Jones Stephens Service Sink Hose with Stainless Bracket. An image showing the black service sink hose coiled, with a brass-colored connector on one end, and a rectangular stainless steel wall bracket with a hose retention mechanism in the center.
Setup
- Inspect Components: Verify that all components are present and undamaged. The package should include the service sink hose and the stainless steel wall bracket.
- Select Mounting Location: Choose a suitable location near your service sink for the stainless steel bracket. Ensure the surface is sturdy and can support the bracket and hose.
- Mount the Bracket: Using appropriate fasteners (not included), securely attach the stainless steel bracket to the wall. Ensure it is level and firmly fixed.
- Connect the Hose: Attach the threaded end of the service sink hose to a compatible water supply faucet or fixture. Hand-tighten first, then use a wrench for a snug fit, being careful not to overtighten.
- Secure the Hose: Place the hose into the bracket's retention mechanism to keep it organized and prevent it from falling.
Operating Instructions
- Water Supply: Ensure the water supply to the faucet or fixture is turned on.
- Using the Hose: Remove the hose from the bracket. Direct the nozzle towards the area requiring water.
- Flow Control: Adjust the water flow using the faucet or fixture controls.
- After Use: Turn off the water supply at the faucet. Drain any remaining water from the hose. Return the hose to the stainless steel bracket for storage.
Maintenance
- Regular Cleaning: Clean the exterior of the hose and the stainless steel bracket periodically with mild soap and water. Rinse thoroughly and dry.
- Inspect for Leaks: Regularly check the hose and connections for any signs of leaks, cracks, or wear. Replace the hose if damage is observed.
- Bracket Inspection: Ensure the mounting screws for the bracket remain tight. Tighten if necessary.
- Storage: When not in use, store the hose securely in its bracket to prevent kinking or damage.
Troubleshooting
- Low Water Pressure:
Possible Cause: Partially closed water supply valve or kinked hose.
Solution: Ensure the water supply valve is fully open. Check the hose for any kinks and straighten them.
- Leaks at Connections:
Possible Cause: Loose connection or damaged washer.
Solution: Tighten the hose connections. If leaks persist, inspect and replace the rubber washer inside the hose connector if it is worn or damaged.
- Hose Not Staying in Bracket:
Possible Cause: Bracket mechanism is loose or hose is improperly placed.
Solution: Ensure the hose is correctly seated in the bracket's retention mechanism. Check if the bracket itself is securely mounted to the wall.
Specifications
| Feature | Detail |
|---|---|
| Brand | Jones Stephens |
| Model Number | M05001 |
| Material | Stainless Steel (Bracket), Hose material not specified but appears rubber/PVC |
| Item Weight | 1.4 pounds |
| Product Dimensions | 10 x 8.5 x 4.7 inches |
| UPC | 717510055016 |
| ASIN | B00I3PIMCC |
Warranty Information
Specific warranty details for the Jones Stephens Corp Service Sink Hose with Stainless Bracket (Model M05001) are not provided in this manual. For comprehensive warranty information, please refer to the documentation included with your purchase or contact Jones Stephens directly through their official website or customer service channels.
Support
For further assistance, technical support, or inquiries regarding the Jones Stephens Corp Service Sink Hose with Stainless Bracket, please contact Jones Stephens customer service. Visit the official Jones Stephens website for contact details and additional resources.
Note: Always ensure to use genuine replacement parts if any components require replacement.
