1. Product Overview
The Genie G1T is a single-button remote control designed for convenient access to your garage. It features Intellicode technology for enhanced security and operates on dual frequencies (315/390 MHz) to minimize interference, ensuring reliable performance.
Image: The Genie G1T single button garage door opener remote, featuring a black casing and a single control button.
2. Compatibility
This remote is compatible with all Genie Intellicode garage door openers manufactured since 1995. It can serve as a replacement for older Genie Intellicode remote models such as GIT-1 and ACSCTG Type 1.
Image: A graphic illustrating the Genie G1T remote as a suitable replacement for several previous Genie Intellicode remote designs.
3. Package Contents
Your Genie G1T remote package includes the following items:
- Genie G1T Single Button Garage Door Opener Remote
- Visor Clip
- CR2032 Lithium Metal Battery (pre-installed)
- Programming Instructions
Image: The Genie G1T remote shown with its included visor clip, designed for easy attachment to a vehicle's sun visor.
4. Setup and Programming
Follow these steps to program your Genie G1T remote to your garage door opener. Ensure you are near your garage door opener unit during this process.
Image: A visual guide detailing the four steps required to program Genie 1-4 button remotes.
Programming Steps:
- Step One: Remove the battery pull tab to activate the remote.
- Step Two: Locate either a square PROGRAM/SET button (PRGM) or a round LEARN CODE button on the opener (typically found on the ceiling-mounted unit).
- Step Three: Press and hold down the PRGM/SET or LEARN CODE button until the LED lights, then release it.
- Step Four: Holding the remote at least 5 feet away from the opener, press and release the desired remote button once every 2 seconds until the opener operates (e.g., the garage door moves).
5. Operating Instructions
Once programmed, operating your Genie G1T remote is straightforward. Simply press the single button on the remote to open or close your garage door. The remote's patented auto-seek dual frequency technology (315/390 MHz) provides strong, secure signals that minimize interference and improves performance.
Image: A hand holding the Genie G1T remote from inside a car, demonstrating its use to open a garage door.
6. Maintenance
Battery Replacement
The Genie G1T remote uses one CR2032 Lithium Metal battery. The average battery life is approximately 2 years, but this can vary based on usage and environmental conditions.
To Replace the Battery:
- Carefully open the remote casing.
- Remove the old CR2032 battery.
- Insert a new CR2032 battery with the positive (+) side facing up.
- Close the remote casing securely.
No reprogramming is typically required after battery replacement, as the remote's code is stored internally.
7. Troubleshooting
Remote Not Working After Programming:
Ensure the battery pull tab was completely removed. Verify the battery is correctly installed with the positive (+) side facing up. Repeat the programming steps, ensuring the remote button is pressed within 30 seconds of pressing the opener's learn button. Consult your garage door opener's manual for specific learn button location and behavior.
Limited Range:
Check the battery level; replace if necessary. Ensure there are no significant obstructions between the remote and the garage door opener. Large metal objects, certain electronic devices, or even a vehicle's sun visor can sometimes interfere with the signal. Try repositioning the remote or your vehicle.
Garage Door Opens/Closes Unexpectedly:
The Genie G1T remote utilizes Intellicode technology designed to prevent unauthorized access. If unexpected operation occurs, it is recommended to clear all existing remotes from the opener's memory and then reprogram them one by one. Refer to your garage door opener's manual for instructions on clearing its memory.
8. Technical Specifications
- Model: G1T
- Part Number: 38501R
- Dimensions: 3.8 x 1.75 x 1.25 inches
- Item Weight: 0.48 ounces
- Material: Plastic
- Battery Type: 1 Lithium Metal (CR2032), included
- Frequency: Dual frequency (315/390 MHz)
- Special Features: Ergonomic design, Intellicode Technology, Patented Auto-Seek Dual Frequency Technology
- Compatibility: Genie Intellicode Garage Door Openers (manufactured since 1995)
- Max Number of Supported Devices: 1
9. Warranty and Customer Support
The Genie G1T remote comes with a Limited 1-Year Warranty. For technical assistance, warranty claims, or further inquiries, please contact Genie customer support directly.
Manufacturer: Genie
Date First Available: November 5, 2013
