Introduction
This manual provides detailed instructions for the setup, operation, and maintenance of your HMDX HX-B320 Sleep Station Plus Projection and Weather Alarm Clock. Please read this manual thoroughly before using the device to ensure proper function and to maximize your user experience.
Product Features
- Projects time and indoor/outdoor temperature onto a ceiling or wall.
- Measures and displays indoor and outdoor temperature.
- Digital FM radio for listening to your favorite stations.
- Dual alarm clock with snooze and gradual wake features.
- Retractable 3.5mm audio cable for connecting external music devices.
- USB port for charging compatible devices.
Package Contents
Verify that all items are present in the package:
- HMDX HX-B320 Sleep Station Plus unit
- Outdoor temperature sensor
- Power adapter
- User manual (this document)
Setup
1. Power Connection
Connect the provided power adapter to the "DC IN 5V" port on the back of the Sleep Station Plus unit. Plug the other end into a standard wall outlet. The unit will power on and the display will illuminate.
Image 1: Rear view of the HMDX HX-B320 Sleep Station Plus, highlighting the DC IN 5V power input and the projector lens.
2. Outdoor Temperature Sensor Setup
- Open the battery compartment on the outdoor sensor.
- Insert the required batteries (typically AA or AAA, refer to sensor markings) ensuring correct polarity.
- Close the battery compartment.
- Place the sensor outdoors within 30 feet (approximately 9 meters) of the main unit, in a shaded area protected from direct sunlight and rain for accurate readings.
- The main unit should automatically detect the sensor and display the outdoor temperature. If not, refer to the troubleshooting section.
Image 2: The HMDX outdoor temperature sensor, a compact silver unit designed for external placement.
3. Setting the Time
- Press and hold the TIME SET button located on the unit.
- While holding TIME SET, use the HOUR and MINUTE buttons to adjust the time.
- Release the TIME SET button when the correct time is displayed.
4. Setting Alarms (Alarm 1 & Alarm 2)
- Press and hold the desired alarm button (ALARM 1 or ALARM 2).
- While holding the alarm button, use the HOUR and MINUTE buttons to set the alarm time.
- Release the alarm button.
- Press the alarm button again to cycle through alarm modes: OFF, BEEP (standard alarm sound), or RADIO (wake to FM radio). An indicator will show the selected mode.
5. FM Radio Setup
- Extend the FM antenna fully for optimal reception.
- Press the TUNER button to turn on the radio.
- Use the TUNE + or TUNE - buttons to manually adjust the frequency.
- Press and hold TUNE + or TUNE - for automatic scanning to the next available station.
- Adjust the volume using the VOLUME + or VOLUME - buttons.
Operating Instructions
1. Projection Function
- Press the PROJECTOR button to activate the time and temperature projection.
- Rotate the projector lens to adjust the focus of the projected image.
- Adjust the angle of the projector arm to direct the image onto your ceiling or wall.
- Press the PROJECTOR button again to turn off the projection.
2. FM Radio Operation
- To turn on the radio, press the TUNER button.
- Use TUNE + or TUNE - to change stations.
- Adjust the volume with VOLUME + or VOLUME -.
- To turn off the radio, press the TUNER button again.
3. Audio Input (3.5mm)
- Locate the retractable 3.5mm audio cable on the unit.
- Pull out the cable and connect it to the headphone jack or audio output of your external device (e.g., smartphone, MP3 player).
- The unit will automatically switch to AUX input mode.
- Control playback and volume from your connected device.
4. USB Charging
- Connect your USB charging cable (not included) to the USB port on the Sleep Station Plus.
- Connect the other end of the cable to your device (e.g., smartphone, tablet).
- The device will begin charging. Note that charging speed may vary depending on the device.
5. Temperature Display
- The unit displays both indoor and outdoor temperatures.
- Press the °C/°F button to switch between Celsius and Fahrenheit temperature units.
Maintenance
- Cleaning: Use a soft, dry cloth to clean the surface of the unit. Do not use liquid cleaners or abrasive materials.
- Battery Replacement (Outdoor Sensor): Replace batteries in the outdoor sensor annually or when the outdoor temperature display becomes erratic or disappears.
- Storage: If storing the unit for an extended period, disconnect it from power and remove batteries from the outdoor sensor.
Troubleshooting
| Problem | Possible Solution |
|---|---|
| Unit does not power on. | Ensure the power adapter is securely connected to both the unit and a working wall outlet. |
| Outdoor temperature not displayed. |
|
| Projection is blurry or unclear. | Rotate the projector lens to adjust the focus. Ensure the projection surface is within optimal distance. |
| Radio reception is poor. | Fully extend the FM antenna. Reposition the unit or antenna for better signal. |
| Alarm does not sound. | Verify that the alarm is set to BEEP or RADIO mode, not OFF. Check alarm volume for radio alarms. |
Specifications
- Model: HX-B320
- Power Source: Corded Electric (DC IN 5V)
- Display Type: Digital
- Special Features: Projection Clock, FM Radio, Dual Alarm, Snooze, Gradual Wake, Indoor/Outdoor Temperature Display, 3.5mm Audio Input, USB Charging Port
- Outdoor Sensor Range: Up to 30 feet (9 meters)
- Dimensions: (Refer to product packaging for exact dimensions)
- Weight: Approximately 16 ounces (0.45 kg)
- Material: Acrylonitrile Butadiene Styrene
Warranty and Support
For warranty information, technical support, or customer service inquiries, please refer to the manufacturer's official website or contact their customer support line. Keep your purchase receipt as proof of purchase.
Manufacturer: Homedics CE
Brand: Jam Audio