Horizon Treadmill Running Belt Instruction Manual
Model: RST5.6 TM212 2007
Brand: WALKINGBELTS
Introduction
This manual provides essential information for the installation, operation, and maintenance of your new Horizon Treadmill Running Belt, Model RST5.6 TM212 2007. Please read these instructions carefully before proceeding to ensure proper function and longevity of your product.
The WALKINGBELTS 1-ply Sand Blast - Pro Residential Running Belt is a high-quality product fabricated in the USA, designed for optimal performance on compatible treadmills.
Setup and Installation
Before installing the new running belt, ensure your treadmill is unplugged from the power source. Refer to your treadmill's original manufacturer manual for specific instructions on removing the old belt and accessing the motor and deck area.
Important Consideration for Belt Type
This running belt is a 1-ply Sand Blast residential type. It is crucial to use a 1-ply belt for treadmills with smaller motors. Using a 2-ply belt on such treadmills is not recommended as it can cause excessive stress and overheating of the motor, potentially leading to damage and reduced lifespan.
Belt Placement
Carefully position the new running belt onto the treadmill deck, ensuring it is centered and aligned with the rollers. Adjust the tension bolts evenly on both sides until the belt is snug but not overly tight. Over-tightening can cause premature wear on the belt and motor.
Initial Lubrication
Your new WALKINGBELTS running belt comes pre-lubricated with 100% Silicone. This initial lubrication is sufficient for the first period of use. Regular lubrication is essential for maintaining belt performance and extending its life.
Figure 1: The 1-ply Sand Blast - Pro Residential Running Belt, rolled for packaging. Note the durable black surface and the lighter underside.
Operating Instructions
After installation, plug in your treadmill and perform a test run at a slow speed. Observe the belt for any signs of misalignment or unusual noise. If the belt drifts to one side, adjust the tension bolts slightly until it runs centrally.
Belt Alignment
To align the belt, run the treadmill at a low speed (e.g., 2-3 mph). If the belt moves to the right, turn the right rear roller bolt clockwise in quarter-turn increments until the belt centers. If it moves to the left, turn the left rear roller bolt clockwise. Allow the belt to run for a minute after each adjustment to observe the effect.
Belt Tension
Proper belt tension is crucial. The belt should be tight enough not to slip during use but loose enough to allow a hand to slide between the belt and the deck. Over-tensioning can strain the motor and rollers.
Maintenance and Care
Lubrication
Regular lubrication with 100% silicone treadmill lubricant is vital. The frequency depends on usage, but a general guideline is every 3-6 months or after 100-150 hours of use. Lift the belt and apply lubricant directly to the center of the deck, then run the treadmill at a slow speed for a few minutes to distribute it.
Cleaning
Keep the running belt and deck clean. Wipe down the belt surface with a damp cloth to remove dust and debris. Avoid using harsh chemicals that could damage the belt material.
Inspection
Periodically inspect the belt for signs of wear, fraying, or damage. Address any issues promptly to prevent further damage to the treadmill.
Troubleshooting
Belt Slipping
If the belt slips during use, it may be too loose or require lubrication. First, check and adjust the belt tension. If slipping persists, apply silicone lubricant as per the maintenance instructions.
Belt Drifting
If the belt consistently drifts to one side, it requires alignment. Follow the 'Belt Alignment' steps in the Operating Instructions section.
Unusual Noise
Unusual noises can indicate various issues. Check for debris under the belt, ensure proper lubrication, and verify belt tension and alignment. If the noise persists, consult a qualified technician.
Product Specifications
| Attribute | Detail |
|---|---|
| Brand | WALKINGBELTS |
| Model | RST5.6 TM212 2007 |
| Belt Style | Flat Belt |
| Ply | 1-ply |
| Surface Type | Sand Blast - Pro Residential |
| Compatible Devices | Treadmill |
| Pre-lubrication | 100% Silicone |
| Fabrication | Fabricated IN USA |
Warranty and Customer Support
Limited Lifetime Warranty
This WALKINGBELTS Treadmill Running Belt comes with a Limited Lifetime Warranty. For details regarding warranty coverage and terms, please refer to the warranty information provided at the time of purchase or contact WALKINGBELTS customer service.
Contact Information
For technical assistance, troubleshooting, or warranty claims, please contact WALKINGBELTS directly. Contact details can typically be found on the product packaging or the official WALKINGBELTS website.
Manufacturer: WALKINGBELTS
ASIN: B00HDOPRAY
