VONYX VXA-800
Contents
Vonyx VXA-800 Professional Power Amplifier User Manual
Model: VXA-800
1. Introduction
Thank you for purchasing the Vonyx VXA-800 Professional Power Amplifier. This manual provides essential information for the safe and efficient operation of your amplifier. Please read it thoroughly before use and retain it for future reference. The VXA-800 is designed for professional audio applications, offering robust power output and versatile connectivity options.
2. Safety Instructions
WARNING: To reduce the risk of electric shock, do not expose this equipment to rain or moisture. Do not remove the cover. No user-serviceable parts inside. Refer servicing to qualified personnel only.
- Ensure the power supply voltage matches the rating on the unit.
- Do not place the unit on an unstable surface.
- Do not block ventilation openings. Ensure adequate airflow around the unit.
- Protect the power cord from being walked on or pinched.
- Disconnect the unit from the mains power during lightning storms or when unused for long periods.
- Do not insert objects into the ventilation slots.
- Avoid operating the unit in extremely hot, cold, dusty, or humid environments.
3. Product Overview
3.1 Front Panel

Image 1: Front view of the Vonyx VXA-800 amplifier, showing the power switch, channel volume controls, and LED indicators.
- Power Switch: Turns the amplifier on or off.
- Channel 1/2 Volume Controls: Adjusts the output level for each channel.
- LED Indicators: Display power status, signal presence, clip warnings, and protection status.
3.2 Rear Panel

Image 2: Rear view of the Vonyx VXA-800 amplifier, showing all input and output connections, mode switch, and power inlet.

Image 3: Close-up of the rear panel connections, highlighting RCA and 6.3mm jack inputs, NL2 and 6.3mm jack outputs, and screw terminals.
- Inputs (RCA & 6.3mm Jack): Connect audio sources to Channel 1 and Channel 2.
- Outputs (NL2, 6.3mm Jack & Screw Terminals): Connect speakers to the amplifier.
- Mode Switch: Selects between Stereo, Parallel, or Bridge operating modes.
- Ground Lift Switch: Helps eliminate hum caused by ground loops.
- Power Inlet: Connects the amplifier to the mains power supply.
4. Setup and Connections
Follow these steps to set up your Vonyx VXA-800 amplifier:
- Placement: Place the amplifier in a well-ventilated area, preferably in a 19-inch rack (3U space required). Ensure sufficient space for airflow around the unit.
- Input Connections:
- Connect your audio source (mixer, pre-amplifier, etc.) to the RCA or 6.3mm Jack inputs on the rear panel.
- For stereo operation, connect the left channel of your source to CH1 input and the right channel to CH2 input.
- Output Connections (Speakers):
- Connect your speakers to the appropriate output terminals (NL2, 6.3mm Jack, or screw terminals).
- Ensure speaker impedance is within the amplifier's specified range (minimum 4 Ohms per channel in stereo mode).
- For bridge mode, connect the speaker to the designated bridge output terminals and ensure the mode switch is set to "Bridge".
- Mode Selection: Use the "MODE" switch on the rear panel to select the desired operating mode:
- STEREO: Each channel operates independently.
- BRIDGE: Combines both channels for a single, higher power output (mono).
- Power Connection: Connect the power cord to the amplifier's power inlet and then to a suitable mains power outlet (230V AC, 50Hz).
- Initial Power On: Before turning on the amplifier, ensure all volume controls are set to minimum. Then, switch on the amplifier using the front panel power switch.
5. Operating Instructions
Once the amplifier is properly connected, follow these steps for operation:
- Power On: Ensure all connections are secure and turn on the amplifier using the front panel power switch. The power LED should illuminate.
- Volume Adjustment: Slowly increase the volume controls for Channel 1 and Channel 2 to the desired listening level.
- Monitoring LEDs:
- SIGNAL LED: Illuminates when an audio signal is present.
- CLIP LED: Illuminates when the input signal is too high, causing distortion. Reduce the input level from your source or the amplifier's volume controls to prevent clipping.
- PROTECT LED: Illuminates if the amplifier enters protection mode due to overheating, short circuit, or DC offset. Turn off the amplifier, check connections, and allow it to cool down before restarting.
- Ground Lift: If you experience hum or buzzing, try flipping the "GROUND LIFT" switch on the rear panel to isolate the audio ground from the chassis ground.
- Power Off: Before powering off, reduce all volume controls to minimum. Then, switch off the amplifier.
6. Maintenance
Proper maintenance ensures the longevity and optimal performance of your amplifier.
- Cleaning: Use a soft, dry cloth to clean the exterior of the unit. Do not use abrasive cleaners or solvents.
- Ventilation: Regularly check that the ventilation openings are clear of dust and debris. Blocked vents can lead to overheating.
- Storage: If storing the amplifier for an extended period, ensure it is in a dry, dust-free environment.
- Servicing: All internal servicing should be performed by qualified service personnel only.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cord disconnected; no mains power; blown fuse. | Check power cord connection; verify mains power; replace fuse (refer to qualified technician). |
| No sound output | Input cables disconnected; speaker cables disconnected; volume controls at minimum; incorrect mode selection. | Check all input and output cable connections; increase volume; ensure correct operating mode (Stereo/Bridge). |
| Distorted sound (CLIP LED on) | Input signal too high; amplifier overloaded. | Reduce input level from source; lower amplifier volume controls. |
| Hum or buzzing noise | Ground loop; faulty cables. | Engage the "GROUND LIFT" switch; try different cables; ensure proper grounding. |
| Amplifier shuts off (PROTECT LED on) | Overheating; short circuit in speaker wiring; speaker impedance too low. | Turn off and allow to cool; check speaker wiring for shorts; verify speaker impedance matches amplifier requirements. |
8. Specifications
| Feature | Specification |
|---|---|
| Brand | VONYX |
| Model Number | VXA-800 |
| Output Power (8 Ohms) | 2 x 300 W |
| Output Power (4 Ohms) | 2 x 400 W |
| Bridge Mode Power | 800 W |
| Frequency Response | 10 Hz - 20 kHz |
| Signal-to-Noise Ratio | > 90 dB |
| Crosstalk | > 70 dB |
| Damping Factor | > 250 |
| Input Connectors | RCA, 6.3mm Jack |
| Output Connectors | NL2, 6.3mm Jack, Screw Terminals |
| Minimum Speaker Impedance | 4 Ohms (Stereo) |
| Power Supply | 230V AC, 50Hz |
| Dimensions (L x W x H) | 482 x 295 x 88 mm (3U) |
| Weight | 5.9 kg |
9. Warranty and Support
For warranty information and technical support, please refer to the documentation provided at the time of purchase or contact your local Vonyx dealer. Keep your proof of purchase for any warranty claims.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.