1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the TYC 11-5185-00-1 Right Replacement Tail Lamp. This product is designed to meet or exceed original equipment standards, ensuring proper illumination and operational safety for your vehicle. Please read these instructions thoroughly before proceeding with installation.
2. Safety Information
WARNING: Proposition 65 Warning
This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.
Always ensure the vehicle's electrical system is disconnected before performing any electrical work. Wear appropriate personal protective equipment, such as gloves and eye protection, during installation. If you are unsure about any step, consult a qualified automotive technician.
3. Product Overview
The TYC 11-5185-00-1 Right Replacement Tail Lamp is a direct-fit component designed for the passenger side of compatible vehicles. It features an OE-comparable design for seamless integration and includes an integrated wiring harness for straightforward installation.
Key Features:
- OE-Comparable Harness: Designed for hassle-free installation without pigtail connectors.
- Precise Fitment: OE-comparable mounting provisions ensure a drop-in, accurate fit.
- Durability: Undergoes rigorous and accelerated cycling tests to ensure product service quality and longevity.
- Lens Protection: Special coating on the lens surface prevents hazing and fading, maintaining proper illumination and operational safety.
- Compliance: Meets or exceeds DOT/SAE standards, with particular consideration for photometric and safety compliance.
Figure 3.1: Front view of the TYC replacement tail lamp, showcasing the red, amber, and clear lens sections.
4. Installation Instructions
Estimated Installation Time: 15-30 minutes
Tools Required:
- Screwdriver (Phillips or flathead, depending on vehicle fasteners)
- Socket wrench set (if applicable for specific vehicle models)
- Gloves and eye protection
Procedure:
- Prepare Vehicle: Park the vehicle on a level surface and engage the parking brake. Turn off the ignition and remove the key. For added safety, disconnect the negative terminal of the vehicle's battery.
- Access Tail Lamp: Locate the existing tail lamp assembly on the passenger side. Depending on your vehicle model, you may need to open the tailgate or access panel in the trunk/bed area to reach the mounting screws or bolts.
- Remove Old Tail Lamp:
- Unscrew any visible mounting screws or bolts securing the tail lamp to the vehicle body.
- Carefully pull the tail lamp assembly straight out from the vehicle. It may be held by alignment pins or clips.
- Once loose, disconnect the electrical connector(s) by pressing the release tab and pulling apart.
- Remove the old tail lamp completely.
- Inspect New Tail Lamp: Ensure the new TYC tail lamp is free from damage and that the integrated wiring harness and bulb sockets are intact. Note: This product typically includes the lens and housing only, without bulbs. Transfer bulbs from the old assembly if necessary, or install new ones.
- Connect Wiring: Connect the electrical connector of the new TYC tail lamp's harness to the vehicle's wiring harness. Ensure a secure connection.
- Install New Tail Lamp:
- Align the new tail lamp with the mounting points and alignment pins on the vehicle body.
- Gently push the tail lamp into place until it sits flush with the vehicle's exterior.
- Reinstall the mounting screws or bolts and tighten them securely, but do not overtighten.
- Test Functionality: Reconnect the vehicle's battery (if disconnected). Turn on the ignition and test all tail lamp functions: running lights, brake lights, turn signals, and reverse lights. Ensure all lights illuminate correctly.
- Final Check: Verify that the tail lamp is securely mounted and that there are no gaps between the lamp and the vehicle body.
Figure 4.1: Rear view of the tail lamp assembly, showing the bulb sockets and the integrated wiring harness with connector, ready for installation.
5. Operating Instructions
The TYC 11-5185-00-1 Right Replacement Tail Lamp operates in conjunction with your vehicle's existing electrical system. Once properly installed, its functions (running lights, brake lights, turn signals, reverse lights) will activate automatically when the corresponding vehicle controls are engaged.
Ensure that all light functions are checked periodically to confirm proper operation and visibility, especially before driving at night or in adverse weather conditions.
6. Maintenance
Regular maintenance helps ensure the longevity and optimal performance of your tail lamp.
- Cleaning: Clean the tail lamp lens regularly with a soft cloth and mild automotive soap and water. Avoid abrasive cleaners or harsh chemicals, as these can damage the special protective coating.
- Inspection: Periodically inspect the tail lamp for any signs of damage, cracks, or moisture intrusion. Check the electrical connections for corrosion or looseness.
- Bulb Replacement: If a bulb fails, replace it promptly with a bulb of the correct type and wattage specified by your vehicle manufacturer. Refer to your vehicle's owner's manual for specific bulb types.
7. Troubleshooting
If you encounter issues with your TYC tail lamp, refer to the following troubleshooting guide:
| Problem | Possible Cause | Solution |
|---|---|---|
| Tail lamp not illuminating |
|
|
| Moisture inside the lens |
|
|
| Dim or flickering light |
|
|
If troubleshooting steps do not resolve the issue, please contact TYC customer support or a certified mechanic.
8. Specifications
| Attribute | Detail |
|---|---|
| Brand | TYC |
| Model Number | 11-5185-00-1 |
| Part Type | Right Replacement Tail Lamp (Passenger Side) |
| Color | Red |
| Specific Uses For Product | Rear Lights |
| Vehicle Service Type | Car, Truck |
| Special Feature | Special coating on lens surface |
| Lens Color | Red |
| Lens Material | Plastic |
| UPC | 762405655123 |
| Assembly Required | No (refers to the lamp assembly itself, not installation) |
| Automotive Fit Type | Vehicle Specific Fit |
| Item Weight | 3.03 pounds |
| OEM Part Number | 19169018 |
| ABPA Partslink Number | GM2801186 |
9. Warranty Information
Specific warranty details for the TYC 11-5185-00-1 Right Replacement Tail Lamp are not provided in this manual. Please refer to the product packaging or contact TYC customer support for information regarding warranty coverage and terms.
10. Customer Support
For technical assistance, troubleshooting, or warranty inquiries, please contact TYC customer support through their official website or the retailer where the product was purchased.
TYC Americas Website: www.tyccom.com (Note: This is a general TYC website, specific support contact may vary)
11. Official Product Videos
There are no official product videos from the seller available for this specific model in the provided data.