Chicco NaturalFeeling Baby Bottle 330ml (6M+) Instruction Manual

1. Product Overview

The Chicco NaturalFeeling Baby Bottle is designed to facilitate a natural feeding experience, closely mimicking a mother's breast. This 330ml bottle is suitable for babies aged 6 months and older, featuring an elongated teat specifically shaped for older infants.

Key features include:

• Elongated Teat: Supports the natural tongue movement and promotes efficient swallowing, with a less rounded base for older children's lip support.
• Double Anti-Colic Valve: Engineered to prevent air ingestion, thereby reducing the risk of colic.
• Soft Silicone: Made from extra-soft silicone with reliefs at the base for a comfortable and natural feel.
• Optimal Flow: Designed for a fast flow, suitable for older infants and thicker liquids.

Figure 1: Chicco NaturalFeeling Baby Bottle 330ml (6M+).

2. Components

The Chicco NaturalFeeling Baby Bottle consists of the following parts:

1. Protective Cap: Covers the teat for hygiene and prevents leaks during transport.
2. Teat: Elongated, soft silicone teat with anti-colic valve.
3. Retaining Ring: Secures the teat to the bottle body.
4. Bottle Body: 330ml capacity, made of plastic.

Figure 2: Disassembled view of the Chicco NaturalFeeling Baby Bottle, showing its main components.

3. Setup and Assembly

Before first use, and after each subsequent use, ensure all components are thoroughly cleaned and sterilized (refer to Section 5: Cleaning and Maintenance).

Assembly Steps:

1. Insert the silicone teat into the retaining ring from the top, pulling it through until it is securely seated. Ensure the anti-colic valve is properly aligned.
2. Screw the assembled teat and retaining ring onto the bottle body until tight.
3. Fill the bottle with the desired liquid.
4. Place the protective cap over the teat to maintain hygiene until feeding.

Figure 3: Fully assembled Chicco NaturalFeeling Baby Bottle, ready for use.

4. Operating Instructions (Feeding)

Follow these guidelines for safe and effective feeding:

• Preparation: Always prepare formula or breast milk according to manufacturer instructions or healthcare professional advice.
• Temperature Check: Before feeding, always check the liquid temperature by shaking a few drops onto the inside of your wrist. It should feel lukewarm, not hot.
• Feeding Position: Hold your baby in a comfortable, semi-upright position. Ensure the teat is full of liquid to minimize air intake.
• Flow Rate: The elongated teat is designed for a fast flow, suitable for babies 6 months and older. Monitor your baby's feeding pace.
• Do Not Microwave: Never heat the bottle in a microwave oven, as this can cause localized overheating and burn your baby.
• Supervision: Always supervise your baby during feeding. Do not use feeding teats as soothers. Continuous and prolonged sucking of fluids can cause tooth decay.

5. Cleaning and Maintenance

Proper cleaning and sterilization are crucial for your baby's health.

Before First Use:

Disassemble all parts and wash them thoroughly in warm soapy water. Rinse well and sterilize using one of the methods below.

Daily Cleaning:

1. Immediately after each use, disassemble the bottle completely.
2. Wash all components (bottle, teat, retaining ring, cap) in warm soapy water. Use a bottle brush for thorough cleaning of the bottle interior and a small brush for the teat.
3. Rinse all parts thoroughly under running water to remove any soap residue.

Sterilization Methods:

• Boiling: Place all disassembled components in a pot of boiling water for 5 minutes. Ensure there is enough water to cover all parts and prevent them from touching the bottom of the pot.
• Steam Sterilizer: Follow the manufacturer's instructions for your electric or microwave steam sterilizer.
• Cold Water Sterilization: Use a sterilizing solution according to the manufacturer's instructions.
• Dishwasher: The bottle body and retaining ring are dishwasher safe (top rack only). Teats should ideally be hand-washed and sterilized separately to prolong their life.

After sterilization, allow parts to cool and dry in a clean, dust-free environment. Store assembled or disassembled in a clean container.

Important: Inspect the teat regularly for signs of wear, damage, or stickiness. Replace immediately if any damage is observed. Silicone teats can absorb odors or colors from food; this is normal and does not affect performance.

6. Troubleshooting

7. Specifications

• Brand: Chicco
• Model Number: 80737000000
• Capacity: 330 ml
• Recommended Age: 6 Months +
• Bottle Nipple Type: Vented, Elongated
• Material: Plastic (bottle body), Silicone (teat)
• Product Dimensions: 16.54 x 18.9 x 4.72 inches (approximate packaging dimensions)
• Item Weight: 1 Kilogram (approximate shipping weight)
• Manufacturer: CHICCO (ARTSANA SpA)

8. Warranty and Support

For warranty information, product support, or to purchase replacement parts, please visit the official Chicco website or contact their customer service department. Keep your purchase receipt as proof of purchase.

You can find more information and contact details on the Chicco Store on Amazon.