1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your HJC HJ-09 Series Dark Smoke Pinlock Ready Helmet Shield. This shield is designed for specific HJC helmet models to enhance rider visibility and comfort.
The HJC HJ-09 shield features an anti-scratch hard coating for durability and is Pinlock ready, allowing for the installation of an anti-fog insert (sold separately).

Image 1: HJC HJ-09 Series Dark Smoke Helmet Shield
2. Helmet Compatibility
The HJC HJ-09 Series Helmet Shield is compatible with the following HJC helmet models:
- AC-12
- CL-15
- CL-16
- CL-17
- CL-SP
- CS-R1
- CS-R2
- CS-R3
- FS-10
- FS-15
- IS-16
- FG-15
3. Setup and Installation
3.1. Shield Installation
To install or replace your HJ-09 helmet shield, follow these steps. For visual guidance, please refer to the embedded video below.
- Open the shield fully to its uppermost position.
- Locate the base plate levers on both sides of the helmet.
- Pull back on the base plate lever while gently pulling the shield outwards and away from the helmet to release it. Repeat for the other side.
- To install the new shield, align the top tab of the shield with the top slot on the base plate.
- Push inward on the shield until it clicks securely into place. Repeat for the other side.
- Ensure both sides are properly secured before use.
Video 1: HJC HJ-09 Replacement Shield Installation Guide by The Helmet Shop
3.2. Pinlock System (If Applicable)
The HJ-09 shield is Pinlock ready. A Pinlock lens (sold separately) creates an airtight chamber between the shield and the lens, preventing fogging. The eccentric pins allow for adjustment to ensure a proper seal.

Image 2: Diagram illustrating Pinlock prepared face shield, Pinlock lens, and Pinlock installed.
4. Operating Considerations
The Dark Smoke tint of this shield is designed for use in bright daylight conditions. It significantly reduces light transmission and is not recommended for night use or in low-light conditions, as it may impair visibility and compromise safety.
4.1. Tint Options
Various tint options are available for the HJ-09 shield to suit different riding conditions and personal preferences. These include Deep Smoke, Mirrored/Silver, Smoke Revo Red, Blue, Rainbow, Light Smoke, and Gold.
Video 2: SoMan HJ-09 Visor Replacement - Colors Compilation
5. Maintenance
Proper maintenance ensures the longevity and clarity of your helmet shield.
- Cleaning: Use only warm, soapy water and a soft microfiber cloth to clean the shield. Avoid abrasive cleaners or harsh chemicals, as these can damage the anti-scratch coating and tint.
- Baseplate Screws: Periodically check and tighten the baseplate screws to ensure the shield remains securely attached to the helmet.
- Storage: Store your helmet and shield in a protective bag or case when not in use to prevent scratches and damage.
6. Specifications
| Feature | Detail |
|---|---|
| Brand | HJC |
| Model Name | HJ-09 |
| Color | Dark Smoke |
| Special Feature | Scratch Resistant, Pinlock Ready |
| Outer Material | Polycarbonate (PC) |
| Item Weight | 5.3 Ounces |
| Item Model Number | K152245 |
7. Troubleshooting
If you encounter any issues with your HJC HJ-09 helmet shield, consider the following:
- Fogging: Ensure your Pinlock lens (if installed) is properly seated and sealed. If fogging persists, consider replacing the Pinlock lens.
- Loose Shield: Check that the baseplate screws are tightened and the shield is correctly clipped into the base plates on both sides.
- Scratches: Minor scratches may be unavoidable over time. For significant scratches affecting visibility, replacement of the shield is recommended.
For further assistance, please contact HJC customer support or your authorized dealer.
8. Warranty and Support
Your HJC HJ-09 Series Helmet Shield is covered by the manufacturer's warranty against defects in materials and workmanship. Please refer to the warranty information provided with your original helmet purchase or visit the official HJC website for details.
For product support, inquiries, or to purchase replacement parts, please visit the HJC Store on Amazon or contact HJC customer service directly.