Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Tunze USA 6105.000 Stream Propeller Pump. Designed for aquariums from 200 to 2,000 liters (50 to 525 US gal.), this pump offers efficient water circulation with electronic speed control. Please read this manual thoroughly before use to ensure proper function and longevity of your device.
Safety Information
- Always disconnect power before performing any maintenance or installation.
- Do not operate the pump out of water.
- Ensure all electrical connections are dry and secure.
- Keep out of reach of children.
- This product is designed for indoor aquarium use only.
Product Overview
The Tunze USA 6105.000 Stream Propeller Pump is a high-performance water circulation device featuring electronic speed control and a strong magnet mount.
Key Components
- Pump Unit: The main body containing the motor and propeller.
- Propeller: Designed for efficient water flow.
- Magnet Holder: For secure attachment to aquarium glass up to 15mm (1/2") thickness.
- Power Supply Unit: Converts household current to the required 24V.
- WIDE FLOW Propeller Housing: An additional accessory for broader water dispersion.
- Controller Compatibility: Can be controlled by Tunze controllers 7092, 7095, and 7096 (controller sold separately).
An overhead view of the Tunze USA 6105.000 Stream Propeller Pump alongside its electronic controller. The pump features a black, ribbed housing and a blue propeller visible through the front grille. The controller is black with blue and white labels, showing various settings like food timer, pulse, auto adjust, wave ok, and external control.
A close-up view of the Tunze USA 6105.000 Stream Propeller Pump and its electronic controller. The pump's black housing and blue propeller are clearly visible, along with the power cable. The controller displays various function settings and adjustment knobs.
Setup
Unpacking and Inspection
Carefully remove all components from the packaging. Inspect for any signs of damage.
Placement
Position the pump inside your aquarium using the magnet holder. Ensure the magnet holder is securely attached to both the inside and outside of the aquarium glass. The pump can be adjusted in 3D for optimal flow direction.
Electrical Connection
Connect the pump to the power supply unit. Plug the power supply unit into a suitable electrical outlet. Ensure a drip loop is formed with the power cord to prevent water from traveling along the cord to the outlet.
Optional: Wide Flow Propeller Housing Installation
The pump comes with an additional WIDE FLOW propeller housing. To install it:
- Gently remove the standard propeller housing by twisting or pulling it off.
- Align the WIDE FLOW housing with the pump unit and push it firmly into place until it clicks.
Video demonstrating how to disassemble Tunze Stream pumps for maintenance. It shows how to remove the front grille, detach the propeller, and access the internal components for cleaning or replacement. This process is essential for installing the optional Wide Flow Propeller Housing or performing routine maintenance.
Operating Instructions
Initial Start-up
Once installed and connected, the pump will begin operating.
Flow Rate Adjustment
The pump features electronic speed control. If using a compatible Tunze controller (7092, 7095, or 7096), refer to the controller's manual for detailed instructions on adjusting flow rate, pulse modes, and other advanced settings.
The flow rate can be adjusted from 3,000 up to approximately 13,000 liters per hour (700 to approximately 3,400 US gallons per hour).
Quiet Operation
This pump is designed for quiet operation. If you experience unusual noise, refer to the Troubleshooting section.
Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your Tunze Stream Propeller Pump.
Cleaning the Pump
- Disconnect the pump from the power supply.
- Remove the pump from the aquarium.
- Disassemble the pump by carefully removing the front grille and propeller.
- Clean all components, including the propeller and pump housing, with a soft brush and warm water. Avoid using harsh chemicals or abrasive materials.
- Inspect the ceramic bearings and shaft for any wear or damage.
- Reassemble the pump, ensuring all parts are correctly seated.
Shaft and Bearing Inspection
Periodically check the ceramic shaft and bearings for any signs of wear or accumulation of debris. Replace if necessary.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump not running | No power | Check power connection and outlet. |
| Pump not running | Propeller jammed | Disconnect power, remove propeller, clean any obstructions. |
| Reduced flow | Clogged intake/propeller | Clean the pump components as described in the Maintenance section. |
| Excessive noise | Debris in pump / Worn bearings | Disassemble and clean the pump. Inspect and replace worn bearings if necessary. |
| Excessive noise | Improper installation | Ensure pump is securely mounted and not vibrating against aquarium glass. |
If issues persist after attempting these solutions, please contact Tunze customer support.
Specifications
- Model: 6105.000
- Flow Rate: 3,000 to approx. 13,000 l/h (700 to approx. 3,400 US gal./h)
- Voltage: 24V
- Energy Consumption: Max. 35W
- Power Supply Unit: 100-240V / 50-60Hz
- Cable Length: 5m (196.8 in.)
- Dimensions: Diameter 90mm (3.5 in.), Output: Diameter 50mm (1.96 / 2.48 in.)
- Magnet Holder: Suitable for glass thickness up to 15mm (1/2")
- Weight: 2 Pounds
- Material: Plastic
- Color: Black
An image showing the packaging of the Tunze Stream 6105 pump, held by hands, with a ruler indicating a height of 7.0 inches (17 cm). This provides a visual reference for the product's size.
Warranty and Support
For warranty information and technical support, please visit the official Tunze USA website or contact their customer service department.
Tunze USA Store: Visit the Tunze Store on Amazon
