1. Introduction
This manual provides comprehensive instructions for the setup, operation, and maintenance of your TELECO TXP-433-A04 remote control. Please read this manual carefully before using the device to ensure proper functionality and safety.
The TELECO TXP-433-A04 is a 4-button gate remote control operating at a frequency of 433.92 MHz. It is designed for easy programming and comes with batteries included.
2. Safety Information
- Battery Safety: Ensure correct battery polarity when inserting. Do not mix old and new batteries. Dispose of used batteries responsibly according to local regulations.
- Children: Keep the remote control out of reach of children to prevent accidental operation or ingestion of small parts.
- Water Exposure: This device is not waterproof. Avoid exposure to water or high humidity.
- Interference: The device operates on a specific frequency. Ensure no other devices are causing interference during operation or programming.
3. Package Contents
Upon opening the package, verify that all items are present and undamaged:
- 1x TELECO TXP-433-A04 Remote Control
- 1x CR2032 Battery (pre-installed or included separately)
- 1x Instruction Manual (this document)
Figure 1: TELECO TXP-433-A04 Remote Control. This image shows the black oval-shaped remote control with four grey circular buttons arranged in a square pattern on its face.
4. Setup and Programming
The TELECO TXP-433-A04 remote control is programmed by recording it into your receiver unit. The exact procedure may vary slightly depending on your specific gate or garage door opener receiver. Refer to your receiver's manual for detailed instructions on how to enter programming mode.
4.1. Battery Installation (if not pre-installed)
- Locate the battery compartment on the back of the remote control.
- Open the compartment using a small screwdriver or by sliding the cover.
- Insert the CR2032 battery, ensuring the positive (+) side faces upwards.
- Close the battery compartment securely.
4.2. Programming the Remote Control to the Receiver
This remote control uses a "recording into receiver" programming method. Follow these general steps:
- Access the receiver unit of your gate or garage door opener. This unit is typically located near the motor.
- Locate the "Learn" or "Program" button on the receiver.
- Press and hold the "Learn" or "Program" button on the receiver for a few seconds until an indicator light (LED) on the receiver illuminates or flashes. This indicates the receiver is in programming mode.
- While the receiver is in programming mode, press the desired button on your new TELECO TXP-433-A04 remote control that you wish to assign to operate the gate/door.
- The indicator light on the receiver should change (e.g., flash rapidly, turn solid, or turn off) to confirm successful programming.
- Wait a few seconds for the receiver to exit programming mode automatically, or press the "Learn" or "Program" button again briefly to exit.
- Test the remote control by pressing the programmed button. The gate or door should respond.
Note: If you encounter difficulties, consult the specific instruction manual for your gate or garage door receiver unit, or contact a qualified technician.
5. Operating the Remote Control
Once programmed, operating the TELECO TXP-433-A04 remote control is straightforward:
- Activation: Press the programmed button on the remote control to activate your gate or garage door opener.
- Range: Ensure you are within the operational range of your receiver unit. Environmental factors can affect signal range.
- Multiple Functions: If you have programmed multiple buttons for different functions (e.g., open/close, pedestrian access), press the corresponding button for the desired action.
6. Maintenance
6.1. Cleaning
To clean the remote control, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the device in water.
6.2. Battery Replacement
When the remote control's range decreases or it stops responding, the battery may need replacement. The TELECO TXP-433-A04 uses a CR2032 lithium battery.
- Open the battery compartment as described in Section 4.1.
- Remove the old CR2032 battery.
- Insert a new CR2032 battery, observing correct polarity (+ side up).
- Close the battery compartment securely.
Important: Dispose of old batteries according to local environmental regulations.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote control does not work. | Dead or low battery. | Replace the CR2032 battery (see Section 6.2). |
| Remote control does not work. | Not programmed correctly. | Re-program the remote control to the receiver (see Section 4.2). |
| Reduced operating range. | Low battery. | Replace the CR2032 battery (see Section 6.2). |
| Reduced operating range. | Interference from other devices. | Ensure no strong radio frequency sources are near the receiver or remote. |
| Gate/door does not respond after programming. | Receiver not in programming mode or programming failed. | Repeat programming steps carefully, ensuring the receiver's indicator light confirms programming mode. Consult receiver manual. |
8. Specifications
- Model: TELECO TXP-433-A04
- Frequency: 433.92 MHz
- Number of Buttons: 4
- Programming Type: Recording into receiver
- Battery Type: 1x CR2032 Lithium (included)
- Dimensions: Approximately 7 mm x 4 mm x 3 mm (0.7 x 0.4 x 0.3 cm)
- Weight: Approximately 26 grams
- Manufacturer: TELECO
9. Warranty and Support
For warranty information, please refer to the terms and conditions provided by your retailer or the official TELECO website. Keep your proof of purchase for any warranty claims.
For technical support or further assistance, please contact your product supplier or an authorized TELECO service center. You may also find additional resources on the official TELECO website.
Manufacturer: TELECO
Model Number: TXP-433-A04
