1. Introduction
This manual provides essential information for the correct installation and maintenance of the Keuco Plan Care Set No. 9, model 34995000200. This set includes critical hardware components designed for securely mounting compatible Keuco bathroom fixtures. Please read these instructions thoroughly before beginning installation to ensure proper function and safety.
2. Package Contents
The Keuco Plan Care Set No. 9 typically includes the following components:
- 2x Hexagonal Screws M10 x 60
- Compatible Wall Anchors (quantity may vary based on specific fixture requirements)
Figure 2.1: Components of the Keuco Plan Care Set No. 9, including hexagonal screws and wall anchors.
3. Setup and Installation
Proper installation is crucial for the stability and safety of your fixture. Always ensure you have the correct tools and follow local building codes.
Required Tools (Not Included):
- Drill
- Appropriate drill bit for wall anchors (refer to anchor specifications)
- Hex key or wrench for M10 screws
- Measuring tape and pencil
- Level
Installation Steps:
- Mark Drilling Points: Position the fixture against the wall and use a pencil to mark the exact drilling points for the mounting screws. Use a level to ensure accurate alignment.
- Drill Holes: Using the appropriate drill bit size for your wall anchors, drill holes at the marked points. Ensure the depth is sufficient for the anchors and screws.
- Insert Wall Anchors: Insert the wall anchors into the drilled holes until they are flush with the wall surface.
- Attach Fixture: Align the fixture's mounting points with the wall anchors. Insert the M10 x 60 hexagonal screws through the fixture and into the wall anchors.
- Tighten Screws: Using a hex key or wrench, carefully tighten the hexagonal screws. Do not overtighten, as this can damage the wall or the fixture. Ensure the fixture is securely fastened and stable.
Figure 3.1: Installation diagram illustrating the screw dimensions and mounting method. The M10 screw has a length of 60mm, with 15.5mm extending into the fixture.
4. Operating Instructions
The Keuco Plan Care Set No. 9 consists of static mounting hardware. It does not require operational instructions. Once installed, its function is to securely hold the attached bathroom fixture in place.
5. Maintenance
To ensure the longevity and continued security of your installed fixture:
- Periodic Inspection: Periodically check the tightness of the screws. If any looseness is detected, gently retighten them.
- Cleaning: If any part of the hardware is exposed, clean it with a soft, damp cloth. Avoid abrasive cleaners or harsh chemicals, as these can damage the finish.
6. Troubleshooting
Most issues related to this mounting set stem from incorrect installation.
- Fixture is Loose:
- Ensure screws are fully tightened into the wall anchors.
- Verify that the correct drill bit size was used for the wall anchors, providing a snug fit.
- Check if the wall material is suitable for the chosen anchors.
- Screw Does Not Tighten:
- The wall anchor may be stripped or damaged. Remove the screw and anchor, and replace the anchor if necessary.
- Ensure the screw is correctly aligned with the anchor.
7. Specifications
| Feature | Detail |
|---|---|
| Brand | Keuco |
| Model Number | 34995000200 |
| Part Number | 34995000200 |
| Item Weight | 2.2 Pounds (approx. 1 kg) |
| Item Dimensions (L x W x H) | 1.97 x 1.97 x 0.79 inches (approx. 5 x 5 x 2 cm) |
| Screw Type | Hexagonal Screw M10 x 60 |
| Manufacturer | KEUCO |
| Global Trade Identification Number (GTIN) | 04017214139361 |
8. Warranty and Support
Information regarding the specific warranty for the Keuco Plan Care Set No. 9 (model 34995000200) was not provided in the product data. For warranty details, technical support, or replacement parts, please contact Keuco directly through their official website or customer service channels. Always refer to the documentation provided with your main Keuco fixture for comprehensive warranty information.