Introduction
This manual provides essential instructions for the proper use, setup, and maintenance of your Geneva Mix Ribbon Bar Watch Faces. Please read this manual thoroughly before use to ensure optimal performance and longevity of the product.
The set includes 10 assorted watch faces, featuring designs from Geneva, Geneva Elite, and Narmi brands. Each watch face comes with a pre-installed battery and a stainless steel back, designed for integration into various jewelry making projects, particularly with ribbon or bar-style watch bands.
Product Components
- 10 x Assorted Watch Faces (Geneva, Geneva Elite, Narmi brands)
- Pre-installed Batteries (one per watch face)
- Stainless Steel Backing on each watch face
Figure 1: An assortment of 10 watch faces. This image displays various shapes including heart, butterfly, round, and square, with different dial colors such as red, blue, green, purple, and yellow. Some faces are branded "NARMI" or "GENEVA".
Setup
The watch faces are designed for integration into custom jewelry pieces. No complex setup is required for the watch faces themselves, as batteries are pre-installed.
- Unpacking: Carefully remove each watch face from its packaging. Inspect for any visible damage.
- Time Setting: To set the time, gently pull out the crown (the small knob on the side of the watch face). Rotate the crown to adjust the hour and minute hands to the correct time. Once set, push the crown back in to start the watch movement.
- Integration: These watch faces are intended to be incorporated into watch bands or other jewelry designs. Ensure the chosen band or setting is compatible with the ribbon bar design of the watch face.
Operating Instructions
Once the time is set and the watch face is integrated into your desired jewelry piece, it operates continuously. The quartz movement ensures accurate timekeeping.
- Time Adjustment: If the time needs to be reset due to time zone changes or daylight saving, follow the "Time Setting" procedure described in the Setup section.
- Battery Life: The pre-installed batteries are designed for long-term use. Battery life can vary depending on environmental conditions and specific watch movement.
Maintenance
Proper maintenance will extend the life and appearance of your watch faces.
- Cleaning: Wipe the watch face and stainless steel back with a soft, dry cloth. Avoid using abrasive cleaners or harsh chemicals, which can damage the finish or the watch mechanism.
- Storage: When not in use or during the jewelry making process, store the watch faces in a dry, dust-free environment, away from direct sunlight and extreme temperatures.
- Water Resistance: These watch faces are not water-resistant. Avoid exposure to water, moisture, and high humidity to prevent damage to the internal components.
- Battery Replacement: When the watch stops or the time becomes inaccurate, it indicates that the battery needs replacement. These watch faces typically use a 377 button cell battery. Battery replacement should ideally be performed by a qualified watch repair technician to avoid damaging the delicate internal mechanism.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Watch is not running or stops intermittently. | Depleted battery. Crown is pulled out. Internal mechanism issue. | Replace battery (recommended by professional). Push crown fully in. Consult a watch repair specialist. |
| Time is inaccurate. | Low battery. Crown not fully pushed in. | Replace battery. Ensure crown is fully pushed in. |
| Condensation under the glass. | Exposure to moisture or humidity. | Immediately cease use and seek professional repair. Avoid further exposure to water. |
Specifications
- Product Type: Watch Faces for Jewelry Making
- Quantity: 10 Pieces (Assorted)
- Brands Included: Geneva, Geneva Elite, Narmi
- Backing Material: Stainless Steel
- Battery Type: Button Cell (e.g., 377) - pre-installed
- Clasp Type: Buckle (Note: This refers to the intended band type for which these faces are designed, not a clasp on the watch face itself.)
- Approximate Package Dimensions: 3.94 x 3.94 x 2.2 inches
- Approximate Item Weight: 7.83 ounces
- Manufacturer: Geneva
- ASIN: B00F589PDU
Warranty Information
Specific warranty details for these watch faces are not provided. For any issues related to manufacturing defects, please contact your point of purchase within the standard return period.
Customer Support
For further assistance or inquiries regarding your Geneva Mix Ribbon Bar Watch Faces, please refer to the seller's contact information on the platform where the purchase was made. For general product information, you may visit the Geneva brand page on Amazon.