Reelcraft L-7050-104-X

Download PDF
Contents

Reelcraft L-7050-104-X Electric Cord Reel Instruction Manual

Model: L-7050-104-X

1. Introduction

This manual provides essential instructions for the safe and efficient installation, operation, and maintenance of your Reelcraft L-7050-104-X Electric Cord Reel. Please read this manual thoroughly before attempting to install or operate the unit. Retain this manual for future reference.

2. Safety Information

General Safety Warnings

  • Always disconnect power to the cord reel before performing any maintenance, inspection, or service.
  • Ensure the cord reel is properly grounded according to all local and national electrical codes.
  • Do not operate the cord reel with a damaged cord. Inspect the cord regularly for cuts, abrasions, or other damage.
  • Keep hands and clothing clear of moving parts during operation.
  • Do not exceed the rated amperage of the cord reel (20A).
  • Install the cord reel in a location free from excessive moisture, dust, or corrosive materials unless specifically designed for such environments.
  • Use only genuine Reelcraft replacement parts for repairs.

3. Product Overview

The Reelcraft L-7050-104-X is a robust electric cord reel designed for industrial and commercial applications. It features a 10/4 gauge, 50-foot long electrical cord with a flying lead end, capable of handling up to 20 amperes.

Components

  • Reel Drum: Houses the electrical cord.
  • Mounting Base: Provides stable support for installation.
  • Electrical Cord: 10/4 gauge, 50 ft. length, 20A rated.
  • Flying Lead End: For direct wiring to a power source.
  • Ratchet Mechanism: Locks the cord at desired lengths.
  • Swivel Assembly: Allows for smooth cord payout and retraction.
Technical drawing of Reelcraft L-7050-104-X Electric Cord Reel with labeled dimensions A, B, C, D, E.

Figure 1: Dimensional drawing of the Reelcraft L-7050-104-X cord reel. Dimensions A, B, C, D, and E indicate overall height, width, mounting width, mounting depth, and total depth respectively, aiding in installation planning.

4. Setup and Installation

Mounting Options

The Reelcraft L-7050-104-X is designed for both freestanding and mounted installations. For optimal performance and safety, mounted installation is recommended.

Mounted Installation

  1. Select Location: Choose a sturdy, flat surface capable of supporting the reel's weight (65 lbs) plus the tension of the cord. Ensure adequate clearance for cord payout and retraction, and access for maintenance.
  2. Secure Mounting Base: Use appropriate hardware (not included) to securely fasten the reel's mounting base to the chosen surface. Refer to Figure 1 for mounting dimensions.
  3. Verify Stability: After mounting, ensure the reel is stable and does not wobble.

Electrical Connection

The cord reel comes with a flying lead end for direct wiring. All electrical connections must be performed by a qualified electrician and comply with all local and national electrical codes.

  • Ensure the power source is disconnected before making any connections.
  • Connect the flying lead end to a dedicated 20A circuit.
  • Properly ground the cord reel to prevent electrical shock.
  • Verify all connections are tight and secure before restoring power.

5. Operating Instructions

Extending the Cord

  1. Grasp the cord firmly and pull it smoothly from the reel.
  2. Pull the cord to the desired length. You will hear a clicking sound as the ratchet mechanism engages.
  3. Once the desired length is reached, stop pulling. The cord will lock in place.

Retracting the Cord

  1. Pull the cord slightly further out (approximately 6-12 inches) to disengage the ratchet mechanism.
  2. Slowly guide the cord back into the reel. Do not release the cord abruptly, as this can cause damage to the reel or the cord.
  3. Ensure the cord retracts evenly and without kinks.

Overload Protection

The cord reel may include an internal circuit breaker for overload protection. If the power is interrupted during use, check the circuit breaker on the reel (if present) and your main electrical panel. Reset the breaker if tripped, and reduce the load if necessary.

6. Maintenance

Regular Inspection

  • Cord: Periodically inspect the entire length of the electrical cord for any signs of wear, cuts, fraying, or damage. Replace damaged cords immediately.
  • Mounting: Check the mounting hardware for tightness and ensure the reel remains securely fastened.
  • Operation: Verify that the cord extends and retracts smoothly and that the ratchet mechanism engages and disengages properly.

Cleaning

Keep the exterior of the cord reel clean and free of excessive dirt, dust, and debris. Use a damp cloth for cleaning. Do not use harsh chemicals or abrasive cleaners.

Lubrication

The internal spring mechanism and swivel may require occasional lubrication. Consult Reelcraft's official service guidelines or contact customer support for recommended lubricants and procedures.

7. Troubleshooting

ProblemPossible CauseSolution
Cord does not retract fully or smoothly.Cord is tangled or kinked; spring tension is low; ratchet mechanism is stuck.Pull cord out completely and guide it back in slowly; consult service for spring tension adjustment or ratchet repair.
Cord does not lock in place.Ratchet mechanism is worn or dirty.Clean the ratchet mechanism; if worn, contact service for replacement parts.
No power at the cord end.Circuit breaker tripped; loose electrical connection; damaged cord.Check and reset the circuit breaker on the reel or main panel; inspect and tighten all electrical connections; replace damaged cord.

8. Specifications

  • Brand: Reelcraft
  • Model: L-7050-104-X
  • Cord Length: 50 ft.
  • Cord Gauge: 10/4
  • Amperage: 20A
  • Material: Steel
  • Color: Red
  • Product Dimensions (L x W x H): 7.88 x 19.75 x 20.25 inches
  • Item Weight: 65 Pounds
  • Installation Type: Freestanding, Mounted
  • Operation Mode: Automatic
  • UPC: 699567007418
  • Date First Available: August 27, 2013

9. Warranty and Support

For detailed warranty information, technical assistance, or to purchase replacement parts, please contact Reelcraft customer support directly. Refer to the official Reelcraft website for the most current contact details and service policies.

You can also visit the Reelcraft store on Amazon for product information and customer reviews:

Visit the Reelcraft Store on Amazon

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.