1. Introduction
This manual provides essential information for the proper installation, maintenance, and troubleshooting of the Fleck 2510 Tank Slip Ring, part number 19197. This component is crucial for maintaining the integrity of your Fleck 2510 and 2510 SXT water softener and filter systems by preventing leaks at the control valve base.
2. Product Overview
The Fleck 2510 Tank Slip Ring (part 19197) is a genuine Fleck replacement component designed to secure the control valve to the tank, preventing leaks where the valve seals against the tank. It is compatible with all Fleck 2510 and 2510 SXT softener, filter, and air injection valves. A common issue leading to leaks in this area is a cracked or damaged slip ring.
Figure 1: The Fleck 2510 Tank Slip Ring (part 19197). This black plastic ring is essential for sealing the control valve to the water tank, preventing water leaks.
Figure 2: A side view of the Fleck 2510 Tank Slip Ring, showing its profile and construction. This view highlights the specific design that allows it to fit securely around the valve base.
3. Safety Information
- Always shut off the main water supply and depressurize the system before attempting any repairs or maintenance.
- Wear appropriate personal protective equipment, such as gloves and eye protection.
- Ensure the work area is clean, dry, and well-lit.
- If you are unsure about any step, consult a qualified plumbing professional.
- Do not overtighten components, as this can cause damage to plastic parts.
4. Installation (Replacement)
This section outlines the general procedure for replacing a damaged Fleck 2510 Tank Slip Ring. Specific steps may vary slightly depending on your system configuration.
- Prepare the System: Shut off the main water supply to your home or the specific water softener/filter system. Open a nearby faucet to relieve system pressure.
- Bypass the System: If your system has a bypass valve, engage it to isolate the softener/filter from the water flow.
- Disconnect the Control Valve: Carefully disconnect any plumbing connections, drain lines, and electrical connections (if applicable) from the control valve.
- Remove the Control Valve: Lift the control valve assembly off the top of the tank. Be prepared for some residual water to drain.
- Inspect Existing Components: Locate the existing slip ring and the tank O-ring (part number 18303) at the base of the control valve. Inspect both for cracks, brittleness, nicks, or cuts. It is highly recommended to replace the tank O-ring (18303) if it shows any signs of wear, as it also contributes to sealing against leaks in the same area.
- Remove Damaged Slip Ring: Carefully remove the old, damaged slip ring.
- Install New Slip Ring: Place the new Fleck 2510 Tank Slip Ring (19197) onto the base of the control valve. Ensure it is seated correctly. If replacing the O-ring, install the new O-ring (18303) before the slip ring.
- Reinstall Control Valve: Carefully lower the control valve assembly back onto the tank, ensuring the new slip ring and O-ring are properly aligned with the tank opening.
- Reconnect Components: Reconnect all plumbing, drain lines, and electrical connections.
- Restore Water Supply: Slowly open the main water supply and disengage the bypass valve (if used). Check for leaks immediately.
- Check for Leaks: Monitor the area around the control valve for any signs of water leakage. If leaks persist, re-check the installation of both the slip ring and the O-ring.
5. Operating
The Fleck 2510 Tank Slip Ring is a passive mechanical component. Once correctly installed, it functions continuously as part of the control valve assembly to maintain a watertight seal. No active operation or user interaction is required for the slip ring itself.
6. Maintenance
The Fleck 2510 Tank Slip Ring generally requires minimal maintenance. However, periodic inspection is recommended:
- Visual Inspection: During routine system checks or other maintenance, visually inspect the slip ring and the area around the control valve base for any signs of cracking, deformation, or water leakage.
- Leak Detection: If you notice any moisture or water pooling around the base of your control valve, it may indicate a failing slip ring or tank O-ring.
- Replacement: If the slip ring appears damaged or if leaks persist after troubleshooting, replace it with a genuine Fleck 19197 part. Consider replacing the tank O-ring (18303) simultaneously.
7. Troubleshooting
The primary issue related to the tank slip ring is water leakage.
Problem: Water Leakage at Control Valve Base
- Cause: Damaged or improperly seated Fleck 2510 Tank Slip Ring (19197).
- Cause: Damaged or improperly seated Tank O-ring (18303).
- Solution: Shut off water supply, depressurize the system, and carefully remove the control valve. Inspect both the slip ring and the tank O-ring for any damage. Replace any damaged components with genuine Fleck parts. Ensure both are correctly seated during reinstallation.
- Solution: Ensure all plumbing connections to the control valve are secure and not cross-threaded.
8. Specifications
- Part Number: 19197
- Compatible Models: Fleck 2510, Fleck 2510 SXT control valves
- Material: Plastic
- Color: Black
- Approximate Dimensions: 3 x 3 x 1 inches
- Approximate Item Weight: 0.352 ounces
- Manufacturer: Fleck
- UPC: 783583352727
9. Warranty & Support
As a replacement part, the Fleck 2510 Tank Slip Ring (19197) typically carries a limited manufacturer's warranty against defects in materials and workmanship. For specific warranty details, claims, or technical support, please contact Fleck or your authorized Fleck dealer directly. Always use genuine Fleck replacement parts to ensure compatibility and system performance.