Introduction
The DEWALT Miter Saw Blade Adapter Ring, part number 152636-00, is a genuine OEM replacement component designed to ensure proper fitment of saw blades with larger arbor holes onto miter saws with smaller arbors. This adapter ring facilitates the use of a 1-inch arbor saw blade on miter saws designed for a 5/8-inch arbor, maintaining blade stability and operational safety. This package includes two adapter rings.
Image: Two DEWALT miter saw blade adapter rings (part number 152636-00). These black plastic rings are essential for adapting saw blades to different arbor sizes.
Compatibility
These adapter rings are compatible with a wide range of DEWALT miter saws that utilize a 5/8-inch arbor and require adaptation for 1-inch arbor saw blades. Refer to your saw's manual for specific arbor size requirements.
Compatible DEWALT Miter Saw Models:
- DW704 (Type 2, 3, 4, 4A, 5)
- DW705 (Type 2, 3, 4, 4A, 5, 6, 7, 8)
- DW705-220 (Type 1, 2)
- DW705S (Type 5, 6, 7, 8)
- DW706 (Type 1)
- DW708 (Type 1, 3, 4)
- DW715 (Type 1, 2, 3)
- DW716 (Type 1, 2, 3)
- DW718 (Type 1, 2, 3)
- DWS780 (Type 1)
- Also compatible with models: 3660 (Type 2, 3), 3680 (Type 2, 3), DW705-35 (Type 2, 3, 4), DW705-44 (Type 2), DW705-AR (Type 6), DW705-B2 (Type 4, 5, 6, 7), DW705-B3 (Type 5, 6, 7).
Setup and Installation
Proper installation of the blade adapter ring is crucial for safe and effective saw operation. Always ensure the saw is unplugged from its power source before performing any maintenance or blade changes.
- Disconnect Power: Unplug the miter saw from the electrical outlet to prevent accidental startup.
- Remove Outer Flange and Blade Bolt: Follow your miter saw's specific instructions to remove the blade bolt and the outer blade flange.
- Remove Old Blade (if applicable): Carefully remove the existing saw blade.
- Insert Adapter Ring into New Blade: Take the new saw blade with a 1-inch arbor hole. Place one DEWALT 152636-00 adapter ring into the larger arbor hole of the new blade. Ensure it sits flush and securely within the blade's center hole. The adapter ring reduces the 1-inch hole to a 5/8-inch opening.
- Mount New Blade: Position the new blade (with the adapter ring installed) onto the miter saw's 5/8-inch arbor shaft. Ensure the blade's teeth are oriented correctly for cutting (usually pointing downwards towards the fence).
- Reinstall Outer Flange and Blade Bolt: Place the outer blade flange back onto the arbor shaft, securing the blade and adapter ring in place. Reinstall and tighten the blade bolt according to your saw's torque specifications. Do not overtighten.
- Verify Security: Gently rotate the blade by hand to ensure it spins freely and is securely mounted without wobble.
Always refer to your specific miter saw's instruction manual for detailed blade changing procedures and safety guidelines.
Operation
Once correctly installed, the blade adapter ring functions as an integral part of the blade mounting system. It ensures that a saw blade with a 1-inch arbor hole fits precisely onto a 5/8-inch arbor shaft, preventing blade wobble and maintaining cutting accuracy. The adapter ring should remain seated within the blade's arbor hole during operation.
Do not operate the miter saw if the blade or adapter ring appears loose or improperly seated.
Maintenance
The DEWALT blade adapter ring requires minimal maintenance. Periodically inspect the adapter ring for any signs of wear, damage, or deformation. If the ring appears cracked, bent, or no longer fits snugly within the blade's arbor hole, it should be replaced immediately to ensure safe operation and accurate cuts.
- Cleaning: Keep the adapter rings free from sawdust and debris. A dry cloth or compressed air can be used for cleaning.
- Storage: Store spare adapter rings in a clean, dry place to prevent loss or damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Blade wobbles after installation. | Adapter ring not seated correctly; incorrect adapter ring size; blade bolt not tightened sufficiently; damaged adapter ring. |
|
| Blade does not fit onto the arbor shaft. | Adapter ring not installed; incorrect adapter ring size; debris on arbor shaft or in adapter ring. |
|
| Adapter ring falls out during blade change. | Normal behavior; adapter rings are not permanently affixed to the blade. |
|
Specifications
- Part Number: 152636-00
- Material: Plastic
- Color: Black
- Item Weight: Approximately 0.16 ounces (per ring)
- Product Dimensions: Approximately 6 x 8 x 0.75 inches (packaging dimensions for 2-pack)
- Arbor Compatibility: Adapts 1-inch blade arbor holes to 5/8-inch miter saw arbors.
- Quantity: 2 per package
- UPC: 704660005275
Warranty and Support
This DEWALT product is a genuine OEM replacement part. For specific warranty information regarding replacement parts, please refer to the official DEWALT warranty policy or contact DEWALT customer support directly. Keep your purchase receipt for warranty claims.
For technical assistance or further inquiries, please visit the official DEWALT website or contact their customer service department.
