Panasonic Portable Bidet Handy Toilette DL-P300-K Instruction Manual

Introduction

Thank you for purchasing the Panasonic Portable Bidet Handy Toilette, model DL-P300-K. This device is designed for personal hygiene, offering a convenient and portable solution for cleansing. Please read this manual thoroughly before use to ensure proper operation and maintenance.

Figure 1: Panasonic Portable Bidet Handy Toilette DL-P300-K in its compact form.

Key Features:

• Compact and portable design for travel.
• Two spray intensity settings: High (HI) and Low (LO).
• Integrated water reservoir with a maximum fill line.
• Includes adapters for various water bottle sizes for extended use.
• Operates on two AAA alkaline batteries.

Setup

1. Battery Installation:

1. Locate the battery compartment cap at the bottom of the main unit.
2. Use a flat-head screwdriver or a coin to turn the cap counter-clockwise to unlock and remove it.
3. Insert two AAA alkaline batteries, ensuring the positive (+) and negative (-) terminals align with the indicators inside the compartment.
4. Replace the battery compartment cap and turn it clockwise to lock it securely.

Figure 2: The main unit with the battery compartment visible at the bottom.

2. Filling the Water Reservoir:

1. Remove the outer shell (water tank) from the main unit by pulling it downwards.
2. Fill the outer shell with clean water up to the "Max" line indicated on the side. Do not overfill, as this can prevent proper sealing and lead to leaks.
3. Align the notch on the main unit with the corresponding slot on the outer shell and push the shell upwards until it clicks securely into place. Ensure the rubber seal is properly seated to prevent leaks.

Figure 3: The bidet unit attached to a standard water bottle using an adapter.

Using Water Bottle Adapters: For extended use, you can attach a standard water bottle. The unit comes with two adapters for different thread sizes. Select the adapter that best fits your water bottle and screw it onto the bottle's opening. Then, attach the main bidet unit to the adapter.

3. Attaching the Wrist Strap:

Thread the provided wrist strap through the small loop located near the top of the main unit. This helps prevent accidental drops during use.

Operating Instructions

1. Extend the Nozzle:

Gently push the end of the nozzle to extend it from the main unit. Ensure it is fully extended before use.

Figure 4: Close-up of the bidet nozzle tip.

2. Power On and Adjust Spray:

• Press the HI button for a strong spray or the LO button for a gentle spray. The device will begin pumping water.
• To turn off the spray, press the currently active button (HI or LO) again.

3. Usage Tips:

• Hold the unit with the nozzle pointing towards the desired area.
• Ensure the unit is held upright or at an angle that allows the water to be drawn from the reservoir.
• After use, retract the nozzle by pushing it back into the unit.

Maintenance

1. Cleaning:

• After each use, empty any remaining water from the reservoir.
• Rinse the water reservoir and nozzle with clean water.
• Wipe the exterior of the unit with a soft, damp cloth. Do not use abrasive cleaners or solvents.
• Ensure all parts are dry before reassembling and storing.

2. Storage:

Store the bidet in a cool, dry place away from direct sunlight and extreme temperatures. If storing for an extended period, remove the batteries to prevent leakage.

Troubleshooting

• No water spray or weak spray:
  • Check if the batteries are correctly installed and have sufficient charge. Replace if necessary.
  • Ensure the water reservoir is filled above the minimum level.
  • Verify that the water reservoir is securely attached to the main unit. If overfilled, it might not seal properly, causing it to slip off or leak.
  • Inspect the nozzle tip for any blockages. Clean gently if necessary.
• Water tank detaches easily:
  • Ensure the water reservoir is not overfilled. Water above the "Max" line can prevent a secure fit.
  • Confirm that the reservoir is pushed all the way in and the notch aligns with the slot on the main unit.
  • Check the rubber seal (O-ring) for damage or displacement.
• Unit does not turn on:
  • Check battery orientation and charge.
  • Ensure the battery compartment cap is fully closed and locked.

Specifications

Figure 5: Visual representation of the bidet's dimensions.