1. Product Overview
The Broan-NuTone 69353000 Vent Motor Assembly is a replacement component designed for the exhaust fan portion of specific Broan-NuTone heater models. This assembly is compatible with models 9093, 9093AB, 9093BR, 9093CH, 9093FWH, 9093WH, 9113, and 9113N.
Important Note:
This 69353000 Motor Assembly is specifically for the exhaust fan and will not function as a replacement for the heater motor. If a replacement heater motor is required, please refer to the appropriate part number (e.g., 69355000, if applicable).
Image 1.1: The Broan-NuTone 69353000 Vent Motor Assembly, showing the motor unit, fan blade, and electrical wiring with connectors.
2. Safety Information
WARNING: Risk of Electric Shock. Disconnect power before servicing.
- Always turn off power at the circuit breaker or fuse box before beginning installation, maintenance, or repair.
- Ensure all electrical connections are made in accordance with local codes and ordinances.
- If you are unsure about any part of the installation process, consult a qualified electrician.
- Wear appropriate personal protective equipment (PPE), such as safety glasses and gloves, during installation.
3. Tools Required
- Phillips head screwdriver
- Flathead screwdriver (small, for prying if needed)
- Wire strippers (if splicing wires is necessary)
- Wire nuts or appropriate connectors (if splicing wires is necessary)
- Molex connector pin removal tool (recommended for easier wire disconnection, or a very small, thin screwdriver)
- 1/8" Allen wrench (may be supplied with the unit for securing the fan cage, or required for older models)
- Pliers
- Voltage tester (to confirm power is off)
4. Setup and Installation
This section outlines the general steps for replacing the vent motor assembly. Specific details may vary slightly depending on your exact Broan-NuTone model.
- Disconnect Power: Locate the circuit breaker controlling the fan unit and turn off the power. Verify power is off using a voltage tester.
- Remove Fan Cover: Carefully remove the decorative grille or cover from the fan unit. This usually involves pulling down on spring clips or unscrewing fasteners.
- Access Motor Assembly: Depending on the model, you may need to remove additional components to access the motor assembly. This often involves unscrewing the existing motor bracket from the housing.
- Disconnect Wiring: Disconnect the electrical wiring from the old motor. Note the position and color of each wire before disconnecting. Some connections may use Molex connectors which require a special tool or careful manipulation with a small screwdriver to release the pins.
- Remove Old Motor Assembly: Once wiring is disconnected, remove the old motor assembly from the fan housing.
- Install New Motor Assembly: Position the new Broan-NuTone 69353000 Vent Motor Assembly into the fan housing. Secure it using the existing screws or mounting hardware. Ensure the fan blade spins freely without obstruction.
- Connect Wiring: Connect the electrical wiring to the new motor assembly, matching the connections noted during disassembly. Ensure all connections are secure. If the new motor's positive wire connector does not match the existing setup (e.g., pin connector instead of a loop terminal), you may need to cut, strip, and splice the appropriate connector from the old motor or use a suitable wire nut.
- Secure Fan Cage (if applicable): If your model includes a separate fan cage, secure it to the motor shaft using the provided Allen wrench or appropriate tool.
- Reassemble Fan Cover: Reattach any removed components and the decorative grille or cover.
- Restore Power: Turn the power back on at the circuit breaker.
- Test Operation: Turn on the fan to ensure it operates correctly and quietly.
5. Operating Instructions
Once installed, the Broan-NuTone 69353000 Vent Motor Assembly operates as part of your existing exhaust fan system. Operation is typically controlled by a wall switch or integrated control panel for your Broan-NuTone heater/fan unit.
- Fan Activation: Activate the fan using the designated switch. The motor assembly will power the exhaust fan to remove moisture and odors from the room.
- Continuous Operation: For optimal moisture control, especially in bathrooms, allow the fan to run for at least 15-20 minutes after showering or bathing.
6. Maintenance
Regular maintenance ensures optimal performance and longevity of your vent motor assembly.
- Cleaning Fan Grille: Periodically remove the fan grille and clean it with a mild detergent and water. Ensure it is completely dry before reattaching.
- Cleaning Fan Blade: With power disconnected, carefully wipe down the fan blade and motor housing to remove dust and debris. Avoid using excessive moisture directly on the motor.
- Lubrication: The motor assembly is typically sealed and does not require lubrication. Do not attempt to lubricate the motor unless specifically instructed by the manufacturer.
- Inspection: Annually inspect the wiring for any signs of wear, fraying, or loose connections.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Fan does not turn on. | No power to the unit. Loose wiring connection. Faulty wall switch. | Check circuit breaker. Verify all wiring connections are secure (with power off). Test or replace wall switch. |
| Fan runs, but is noisy or vibrates excessively. | Fan blade obstructed or dirty. Motor not securely mounted. Damaged fan blade or motor bearings. | Disconnect power and clean fan blade/housing. Ensure motor assembly is tightly secured. If noise persists after cleaning and securing, the motor or blade may be faulty and require replacement. |
| Reduced airflow. | Dirty fan grille or blade. Ductwork obstruction. | Clean fan grille and blade. Inspect ductwork for blockages (may require professional assistance). |
8. Specifications
- Model Number: 69353000
- Brand: Broan-NuTone
- Manufacturer: Nutone
- Compatible Models: 9093, 9093AB, 9093BR, 9093CH, 9093FWH, 9093WH, 9113, 9113N (Exhaust Fan Motor)
- Material: Copper (motor windings)
- Approximate Item Weight: 0.01 Ounces (Note: This weight may refer to a specific component or be an error in source data. Actual assembly weight is typically higher.)
- UPC: 680474796632
9. Warranty and Support
For warranty information and technical support, please contact Broan-NuTone directly. Keep your purchase receipt as proof of purchase for any warranty claims.
Broan-NuTone Customer Service:
- Visit the official Broan-NuTone Store on Amazon for product information.
- Refer to the original documentation provided with your Broan-NuTone fan/heater unit for specific warranty terms.
