NICE WM006G

Download PDF
Contents

NICE NiceWay WM006G 6-Group Automation Remote Control User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the NICE NiceWay WM006G 6-Group Automation Remote Control. Please read this manual carefully before using the device to ensure proper function and safety.

The NiceWay WM006G is a versatile transmitter module designed for controlling up to six groups of automation systems (e.g., gates, blinds, awnings) with open, stop, and close commands. It is part of the NiceWay system, allowing integration into various support models for customized solutions.

2. Safety Information

  • Ensure the device is used within its specified operating conditions.
  • Keep the device away from water and extreme temperatures.
  • Do not attempt to open or repair the device yourself. Refer to qualified personnel for service.
  • Dispose of batteries according to local regulations.

3. Package Contents

  • NICE NiceWay WM006G Transmitter Module
  • 3V Lithium Battery (pre-installed or included)
  • User Manual (this document)

4. Product Overview

4.1. Components and Controls

The WM006G module features a keypad for controlling up to six automation groups. The layout typically includes numbered buttons for group selection and dedicated buttons for 'Up' (Open), 'Stop', and 'Down' (Close) commands.

NICE NiceWay WM006G Remote Control Keypad Layout

Figure 1: Front view of the NICE NiceWay WM006G remote control module, showing six numbered group selection buttons (1-6) and three control buttons for Up, Stop, and Down functions.

5. Setup

5.1. Battery Installation

The WM006G module uses a 3V lithium battery. If the battery is not pre-installed or needs replacement, follow these steps:

  1. Locate the battery compartment on the back of the module.
  2. Open the compartment cover.
  3. Insert the 3V lithium battery, ensuring correct polarity (+/-).
  4. Close the battery compartment cover securely.

5.2. Pairing with Automation System

The WM006G uses 433.92 MHz rolling code technology for secure communication. To pair the remote control with your Nice automation system (e.g., Ergo, Plano, FloR, VeryVR, Flo with WM240C), refer to the specific instructions provided with your automation receiver unit. The general procedure involves activating the receiver's programming mode and then transmitting a signal from the WM006G.

  • Auto-learning: The system supports auto-learning for easy pairing.
  • Compatibility: Compatible with Nice Ergo, Plano, FloR, and VeryVR systems. For Flo systems, compatibility is ensured with WM240C.

6. Operating Instructions

The WM006G allows control of up to six independent automation groups. Each group can be controlled in simple or multi-group mode.

6.1. Selecting a Group

Press the numbered button (1-6) corresponding to the automation group you wish to control. The selected group will typically be indicated by an LED or a specific response from the automation system.

6.2. Sending Commands

  • Open/Up: Press the ▲ (Up arrow) button to open or raise the automation.
  • Stop: Press the STOP button to halt the automation at its current position.
  • Close/Down: Press the ▼ (Down arrow) button to close or lower the automation.

6.3. Multi-Group Control

Specific instructions for multi-group control (e.g., controlling multiple groups simultaneously) may vary depending on the programming of your automation receiver. Refer to your receiver's manual for advanced multi-group functionalities.

7. Maintenance

7.1. Cleaning

Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.

7.2. Battery Replacement

When the battery is low, the remote control's range may decrease, or its indicator light (if present) may signal a low battery. Replace the battery as described in Section 5.1. Use only a 3V lithium battery of the specified type.

8. Troubleshooting

  • Remote not responding:
    • Check battery level and replace if necessary.
    • Ensure the remote is within range of the receiver.
    • Verify that the remote is correctly paired with the automation system (refer to Section 5.2).
  • Reduced range:
    • Replace the battery.
    • Check for obstructions between the remote and the receiver.
    • Ensure no strong radio interference sources are nearby.
  • Automation system not performing desired action:
    • Confirm the correct group is selected.
    • Check the automation system's status and power supply.
    • Refer to the automation system's specific manual for troubleshooting.

9. Specifications

FeatureSpecification
ModelWM006G
BrandNICE
Dimensions41 x 41 x 10 mm
Weight14 g
Frequency433.92 MHz
Coding52-bit rolling code (over 4.5 million billion combinations)
Range (Open Space)200 m
Range (Indoors)35 m
Battery Type3V Lithium Battery
CompatibilityNice Ergo, Plano, FloR, VeryVR (Flo with WM240C)

10. Warranty and Support

The NICE NiceWay WM006G remote control comes with a one-year warranty from the date of purchase. This warranty covers manufacturing defects. The battery and manual are included with the product.

For technical support, warranty claims, or further assistance, please contact your authorized NICE dealer or visit the official NICE website.

© 2023 NICE S.p.A. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.