1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Frigidaire IMK0028A Icemaker Kit. This kit is a genuine OEM replacement part designed to provide a reliable ice production solution for compatible Frigidaire and Electrolux refrigerators. Please read all instructions carefully before beginning installation or operation to ensure proper function and safety.
Note: Frigidaire and Electrolux are interchangeable names for the same brand. The item received may bear either name.
2. Safety Information
- Always disconnect power to the refrigerator before attempting any installation, maintenance, or repair.
- Wear appropriate personal protective equipment, such as gloves, during installation to prevent injury.
- Ensure all connections are secure and properly sealed to prevent water leaks.
- If you are unsure about any part of the installation process, consult a qualified technician.
- Keep children and pets away from the work area during installation.
3. Package Contents
Verify that all components are present before beginning installation:
- Icemaker Assembly
- Ice Storage Bin
- Mounting Brackets (various sizes to fit different models)
- Hardware (screws, clips)
- Water Line Connection Kit (if applicable)
- Instruction Manual (this document)
Image 1: Frigidaire IMK0028A Icemaker Kit showing main components.
4. Setup & Installation
Installation of the IMK0028A Icemaker Kit can be involved and requires careful attention to detail. It is recommended to have basic tool knowledge and mechanical aptitude. The process typically involves removing the freezer door and internal racks.
4.1 Tools Required
- Screwdriver (Phillips and/or flathead)
- Wrench (for water line connections, if applicable)
- Pliers (for clips)
- Gloves
4.2 Pre-Installation Steps
- Disconnect Power: Unplug the refrigerator from the electrical outlet or turn off the circuit breaker.
- Turn Off Water Supply: If your refrigerator has an existing water line, turn off the water supply to the refrigerator.
- Empty Freezer: Remove all food items and shelves from the freezer compartment.
- Remove Freezer Door: Carefully remove the freezer door according to your refrigerator's specific instructions. This often involves disconnecting wiring harnesses and hinge pins.
- Remove Internal Racks/Baskets: Remove any internal racks or baskets to provide clear access to the back panel and mounting locations. This may involve releasing clips.
4.3 Icemaker Installation
- Identify Mounting Location: Locate the designated area for the icemaker assembly, typically on the upper left side of the freezer compartment. Pre-drilled holes and wiring harnesses should be present.
- Select Correct Bracket: The kit includes multiple mounting brackets. Identify the correct bracket for your specific refrigerator model. The icemaker assembly may come with a shorter bracket pre-installed; you may need to swap it for a longer one if required by your model. Secure the chosen bracket to the icemaker assembly with the provided hardware.
- Mount Icemaker Assembly: Align the icemaker assembly with the pre-drilled holes in the freezer wall. Secure it using the provided screws. Ensure it is firmly attached.
- Connect Wiring: Plug the icemaker's electrical harness into the corresponding receptacle in the freezer wall. Ensure a secure connection.
- Connect Water Line: Connect the water supply line to the icemaker's inlet valve. Ensure the connection is tight to prevent leaks. Some models may require replacing a back panel with a new one provided in the kit, though this is not always necessary.
- Install Ice Bin: Place the ice storage bin beneath the icemaker assembly. Ensure it is properly seated and positioned to catch ice.
Image 2: Example of Frigidaire IMK0028A Icemaker Kit installed within a freezer compartment.
4.4 Post-Installation Steps
- Reinstall Racks and Door: Reinstall the internal freezer racks/baskets and the freezer door. Ensure all clips and connections are secure.
- Restore Water Supply: Turn on the water supply to the refrigerator. Check for any leaks around the water line connection to the icemaker.
- Restore Power: Plug the refrigerator back into the electrical outlet or turn on the circuit breaker.
- Initial Ice Production: The icemaker will typically begin producing ice within 12-24 hours. Discard the first few batches of ice to flush the water lines.
5. Operating Instructions
Once installed and powered, the Frigidaire IMK0028A Icemaker Kit operates automatically to produce ice.
- Automatic Operation: The icemaker will fill with water, freeze it, and then eject the ice cubes into the ice storage bin. This cycle repeats automatically as long as the freezer temperature is adequate and the water supply is on.
- Ice Level Sensor: The icemaker is equipped with a sensor (often a wire arm) that detects when the ice bin is full. When the ice reaches a certain level, the icemaker will temporarily stop production until more ice is used.
- Initial Production Time: Allow 12-24 hours for the icemaker to produce its first full batch of ice. Full ice production capacity may take a few days to achieve.
- Ice Bin Management: When pulling out the freezer drawer, ensure the ice bin is not overfilled, as ice may fall out of the back of the bin and obstruct the freezer door's full closure.
6. Maintenance
Regular maintenance helps ensure optimal performance and longevity of your icemaker.
- Clean Ice Bin: Periodically remove and wash the ice storage bin with mild soap and warm water. Rinse thoroughly and dry completely before returning it to the freezer.
- Check Water Filter: If your refrigerator has a water filter, ensure it is replaced regularly according to the refrigerator manufacturer's recommendations. A clogged filter can reduce water flow to the icemaker.
- Inspect Water Line: Occasionally inspect the water supply line for kinks, leaks, or damage.
- Clean Icemaker: If mineral deposits build up on the icemaker components, gently wipe them with a damp cloth. Do not use abrasive cleaners.
7. Troubleshooting
If your icemaker is not functioning as expected, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Icemaker not producing ice. |
|
|
| Low ice production. |
|
|
| Water leaking in freezer. |
|
|
| Ice falling out of bin when drawer is opened. |
|
|
If these solutions do not resolve the issue, contact Frigidaire customer support or a qualified service technician.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Frigidaire |
| Model Number | IMK0028A |
| Part Number | IMK0028A |
| UPC | 012505454028 |
| Product Dimensions (D x W x H) | 1"D x 1"W x 1"H (Note: These dimensions are often placeholder values for small parts and may not reflect the actual installed size.) |
| Item Weight | 5.2 Pounds |
| Material Type | Plastic |
| Wattage | 6.41 watts |
| Included Components | Icemaker Kit, User Manual |
9. Warranty & Support
9.1 Warranty Information
The Frigidaire IMK0028A Icemaker Kit comes with a 1 Year Manufacturer Warranty. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.
For specific warranty terms and conditions, please refer to the documentation included with your original refrigerator or contact Frigidaire customer service.
9.2 Customer Support
For technical assistance, troubleshooting beyond this manual, or warranty service, please contact Frigidaire customer support. You can typically find contact information on the Frigidaire official website or in your refrigerator's main user manual.
Online Resources: Visit the official Frigidaire website for additional support, FAQs, and service locator tools. www.frigidaire.com