ADT Commercial Ice Machine User Manual

Introduction

Thank you for choosing the ADT Commercial Ice Machine, Model HZB-36F. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your new ice maker. Please read this manual thoroughly before operating the appliance and retain it for future reference.

This commercial ice machine is designed to produce up to 80 lbs of clear ice cubes daily, with a storage capacity of 20 lbs. Its compact design allows for flexible installation as an undercounter or freestanding unit.

Important Safety Information

Please read all safety warnings and instructions carefully before use to prevent potential hazards and ensure proper operation.

• Ensure the appliance is properly grounded.
• Do not operate the ice maker with a damaged power cord or plug.
• Keep ventilation openings clear of obstruction.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• This appliance is intended for commercial use.
• Always disconnect the power supply before cleaning or performing maintenance.
• If your drain outlet height is more than 5.9 inches, a drain pump must be configured. The drain outlet should be no further than 12 inches from the ice machine. Failure to do so may result in water leakage.

Product Overview

The ADT Commercial Ice Machine HZB-36F features a durable stainless steel exterior and an intuitive LCD control panel for ease of use.

Key Features:

• Fast Ice Making: Produces 40 clear ice cubes per cycle in 11-20 minutes, with a daily output of up to 80 lbs. Each cube weighs 9g.
• Flexible Installation: Dimensions of 14.96"W x 19.29"D x 33.85"H (including 1.18" adjustable feet) allow for undercounter or freestanding placement. Features a front breathing design.
• LCD Display: User-friendly control panel for power, delay, cleaning, and ice cube size adjustments.
• Durable Design: Stainless steel door with a full-length handle and bright blue LED interior lighting.

Setup and Installation

Proper installation is crucial for the performance and longevity of your ice machine. Please follow these steps carefully.

Unpacking:

1. Carefully remove all packaging materials.
2. Inspect the ice machine for any shipping damage. Report any damage to your supplier immediately.
3. Ensure all accessories are present: Ice Scoop, In-Line Hose, Drain Hose.

Location Requirements:

• Place the ice machine on a flat, stable surface.
• Ensure adequate ventilation around the unit. The front breathing design allows for built-in installation, but clearances should still be maintained as per local codes.
• Avoid direct sunlight or heat sources.
• The ambient temperature should be between 50°F (10°C) and 90°F (32°C).

Water and Drain Connections:

1. Connect the supplied in-line hose to a potable water supply. Ensure the water pressure is within the recommended range (15-80 PSI).
2. Connect the drain hose to a suitable drain. Important: If your drain outlet height is more than 5.9 inches, or if the drain outlet is further than 12 inches from the ice machine, a separate drain pump must be installed. This unit does not include a built-in drain pump.
3. Ensure all connections are secure and leak-free.

Electrical Connection:

• Plug the ice machine into a dedicated, grounded 115V AC outlet.
• Do not use extension cords or adapter plugs.

Operating Instructions

Familiarize yourself with the control panel and basic operations.

Control Panel (Refer to Figure 3):

• Power Button (ON/OFF): Press to turn the unit on or off.
• Timer Setting: Allows you to set a time for the unit to turn on or off automatically.
• Ice Making Time Adjustment (+/-): Increase or decrease the ice making time to adjust ice cube size. Longer time results in larger cubes.
• Clean Function: Press and hold the power button for automatic cleaning.

Initial Operation:

1. After connecting water and power, press the Power button to turn on the unit.
2. The ice making process will begin automatically. The first few cycles may produce smaller or irregular ice cubes. This is normal.
3. Allow the unit to run for several hours to stabilize ice production.

Ice Making Reservation:

The unit supports setting a reservation time for ice making, allowing you to schedule when the ice production starts or stops.

Maintenance and Cleaning

Regular cleaning and maintenance will ensure optimal performance and extend the lifespan of your ice machine.

Daily Maintenance:

• Wipe down the exterior with a soft, damp cloth.
• Ensure the ice scoop is clean and stored hygienically.

Weekly/Bi-Weekly Cleaning:

• Empty the ice storage bin and clean it with a mild detergent and warm water. Rinse thoroughly.
• Clean the water reservoir and ice making components.

Automatic Cleaning Function:

The ice machine is equipped with an auto-cleaning feature for convenience.

1. Ensure the ice bin is empty.
2. Add a small amount of ice machine cleaner (food-grade) to the water reservoir as per cleaner instructions.
3. Press and hold the "Clean" button (often integrated with the Power button, refer to Figure 3) to activate the auto-cleaning cycle.
4. Once the cycle is complete, drain the cleaning solution and rinse the unit thoroughly with fresh water by running several ice-making cycles and discarding the ice.

Condenser Cleaning:

Periodically clean the condenser coils to ensure efficient operation. This should be done by a qualified technician or by following specific instructions in a more detailed service manual.

Troubleshooting

Before contacting customer service, please refer to the following table for common issues and their solutions.

Specifications

Warranty and Customer Support

For warranty information, please refer to the warranty card included with your product or contact ADT customer support directly. Keep your proof of purchase for any warranty claims.

If you encounter issues not covered in the troubleshooting section or require further assistance, please contact ADT customer support. Contact details can typically be found on the manufacturer's website or on the product packaging.

For the latest information and support, please visit the official ADT website or contact their customer service line.