Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Maxxima MWL-01B 6 LED 5" Round Heavy Duty Super Bright Work Light. Please read this manual thoroughly before installation and use to ensure proper function and safety. Keep this manual for future reference.
Product Overview
Components
- Maxxima MWL-01B Work Light Unit
- Mounting Bracket
- Instruction Guide
Features
- 6 LED design for super bright illumination.
- Heavy-duty construction for durability.
- Black housing for robust protection.
- Designed as an auto accessory.
- Compact dimensions for versatile mounting.
Figure 1: Maxxima MWL-01B 6 LED 5" Round Heavy Duty Super Bright Work Light. This image shows the round work light with its black housing, clear polycarbonate lens, and the stainless steel mounting bracket attached at the bottom. The light features a ribbed design on its housing for heat dissipation.
Setup
Mounting Instructions
- Select Mounting Location: Choose a sturdy, flat surface on your vehicle or equipment that can support the light's weight and provide optimal illumination. Ensure the location does not obstruct vision or interfere with other vehicle components.
- Mark Drill Points: Use the mounting bracket as a template to mark the positions for drilling holes.
- Drill Holes: Carefully drill holes of the appropriate size for the mounting hardware.
- Secure Bracket: Attach the stainless steel mounting bracket to the chosen surface using suitable bolts, washers, and nuts (not included). Ensure it is securely fastened.
- Attach Light to Bracket: Mount the work light unit to the bracket using the provided hardware. Adjust the angle of the light as needed before fully tightening the bolts.
Wiring Diagram
The MWL-01B work light operates on 12VDC. Proper wiring is crucial for safe and effective operation.
- Identify Wires: The work light typically comes with two wires: a positive (+) wire (usually red) and a negative (-) wire (usually black).
- Connect Positive: Connect the positive wire of the light to a fused 12VDC power source. It is recommended to use an inline fuse (not included) appropriate for the light's current draw (1.24A). This can be connected to a switch for easy control.
- Connect Negative: Connect the negative wire of the light directly to a reliable chassis ground point on your vehicle or equipment.
- Test Connection: Before finalizing, briefly test the connection to ensure the light functions correctly.
- Secure Wiring: Route and secure all wiring to prevent chafing, pinching, or exposure to excessive heat or moving parts. Use cable ties or conduit as necessary.
Operating Instructions
Once properly installed and wired, operating the Maxxima MWL-01B work light is straightforward:
- Power On: Activate the switch connected to the light's positive power supply. The 6 LEDs will illuminate, providing 550 lumens of bright light.
- Power Off: Deactivate the switch to turn off the light.
- Adjust Angle: If needed, loosen the mounting bolts slightly to adjust the light's angle, then re-tighten securely.
The light is designed for heavy-duty use and provides consistent illumination in various conditions.
Maintenance
The Maxxima MWL-01B work light is designed for low maintenance. Regular inspection and cleaning will help ensure its longevity and optimal performance.
- Cleaning: Periodically clean the lens and housing with a soft cloth and mild soap and water. Avoid abrasive cleaners or solvents that could damage the polycarbonate lens or aluminum housing.
- Inspection: Regularly check the mounting hardware for tightness. Vibrations from vehicle operation can sometimes loosen bolts. Inspect wiring for any signs of wear, fraying, or corrosion.
- Lens Condition: Ensure the lens remains clear and free of significant scratches or cracks that could impede light output.
Troubleshooting
If you encounter issues with your Maxxima MWL-01B work light, refer to the following table for common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply. | Check fuse, wiring connections (positive and negative), and switch operation. Ensure 12VDC is present at the light's input. |
| Light flickers or is dim. | Loose connection or insufficient voltage. | Tighten all wiring connections. Verify battery voltage is adequate (12VDC). Check for corrosion on terminals. |
| Moisture inside the lens. | Seal compromise. | Contact Maxxima customer support. Do not attempt to open the sealed unit. |
| Mounting bracket is loose. | Vibration or improper tightening. | Re-tighten all mounting bolts securely. Consider using thread-locking compound if vibration is severe. |
Specifications
| Attribute | Specification |
|---|---|
| Model | MWL-01B |
| Light Type | LED Work Light |
| Light Output | 550 Lumens |
| Voltage | 12VDC |
| Current Drawn | 1.24A |
| Housing Material | Aluminum (Black) |
| Lens Material | Polycarbonate (Clear) |
| Mounting | Surface Bracket |
| Base Material | Stainless Steel |
| Diameter | 4-1/2 inches |
| Depth | 2-1/4 inches |
| Item Weight | 1.35 pounds |
| Product Dimensions | 10.5 x 0.5 x 5.5 inches |
| Country of Origin | Taiwan, Province Of China |
Warranty and Support
Maxxima products are manufactured to high-quality standards. For specific warranty information regarding your MWL-01B work light, please refer to the warranty card included with your purchase or visit the official Maxxima website. In case of technical issues, questions, or warranty claims, please contact Maxxima customer support through their official channels.
For additional support and product information, you may visit the Maxxima Store on Amazon.
