1. Introduction
This manual provides essential information for the installation, maintenance, and troubleshooting of the Indesit 1920H8 dryer belt. This product is a replacement part designed to restore the functionality of compatible clothes dryers. Please read this manual thoroughly before attempting any installation or repair.
2. Safety Information
Always prioritize safety when working with electrical appliances. Failure to follow these safety guidelines may result in injury or damage to the appliance.
- Disconnect Power: Before beginning any repair or installation, ensure the dryer is completely unplugged from the electrical outlet.
- Professional Installation Recommended: If you are not experienced with appliance repair, it is highly recommended to seek assistance from a qualified technician.
- Wear Protective Gear: Use appropriate personal protective equipment, such as gloves, to prevent injury.
- Inspect for Damage: Before installation, carefully inspect the new belt for any signs of damage. Do not install a damaged belt.
- Keep Children Away: Ensure children and pets are kept away from the work area during installation.
3. Product Overview
The Indesit 1920H8 dryer belt is a flat drive belt essential for the operation of your dryer's drum. It transmits power from the motor to the drum, allowing it to rotate and tumble clothes.
Figure 1: Indesit 1920H8 Dryer Belt. A coiled black flat dryer belt, model 1920H8, designed for appliance repair.
4. Compatibility
This 1920H8 dryer belt is compatible with various dryer models from the following brands:
- INDESIT
- ARISTON
- ARISTON HOTPOINT
- MEA
- CURLING
- LADYWIND
- RECTILIGNE
- DOMEOS
To ensure compatibility, always verify your appliance's specific model number against the product description or consult with a qualified technician.
5. Installation
The following steps provide a general guide for replacing a dryer belt. Specific procedures may vary depending on your dryer model. Refer to your dryer's service manual for detailed instructions.
- Disconnect Power: Unplug the dryer from the electrical outlet.
- Access the Drum: Depending on your dryer model, you may need to remove the top panel, front panel, or rear panel to access the dryer drum and motor assembly.
- Remove Old Belt: Carefully remove the old, broken, or worn-out belt from around the drum and motor pulley. Note its routing for reference.
- Install New Belt: Route the new 1920H8 belt around the dryer drum and then around the motor pulley and idler pulley (if present). Ensure the ribbed side of the belt makes proper contact with the motor pulley.
- Tension Check: Verify that the belt has appropriate tension. It should be snug but not overly tight.
- Reassemble Dryer: Reattach all panels and secure them properly.
- Test Operation: Plug the dryer back in and run a short cycle to ensure the drum rotates smoothly and quietly.
Note: If you encounter any difficulties or are unsure about any step, consult a professional appliance repair technician.
6. Maintenance
Proper maintenance can extend the life of your dryer belt and ensure efficient dryer operation.
- Regular Inspection: Periodically inspect the belt for signs of wear, fraying, cracks, or stretching. Replace the belt if any damage is observed.
- Avoid Overloading: Overloading the dryer can put excessive strain on the belt, leading to premature wear.
- Clean Lint Filter: A clogged lint filter can restrict airflow, causing the dryer to overheat and potentially damage the belt. Clean the lint filter after every load.
7. Troubleshooting
If your dryer is experiencing issues related to the belt, consider the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Dryer drum does not spin | Broken or dislodged drive belt | Inspect and replace the belt if broken. Re-route if dislodged. |
| Squealing or grinding noise | Worn or stretched belt, worn idler pulley | Inspect the belt for wear; replace if necessary. Check idler pulley for smooth operation. |
| Dryer stops mid-cycle | Belt slipping due to wear or overload | Reduce load size. Inspect and replace belt if worn. |
If troubleshooting steps do not resolve the issue, contact a qualified appliance repair technician.
8. Specifications
- Model: 1920H8
- Manufacturer Reference: 481281718177
- Brand: Indesit
- Belt Style: Flat belt
- Compatible Appliances: Dryer
- Compatible Brands: Indesit, Ariston, Ariston Hotpoint, MEA, Curling, Ladywind, Rectiligne, Domeos
9. Warranty and Support
For information regarding the warranty of this product, please refer to the purchase documentation or contact the seller directly. For technical support or further assistance, it is recommended to consult a professional appliance repair service.
This product is supplied by a French seller specializing in appliance spare parts since 1984.
