1. Introduction
1.1. Overview
The Hager WITTY charging station is designed for charging electric vehicles in accordance with Mode 3 (IEC 61851-1) and Mode 2 standards. It supports both Type 3 and standard socket connections, offering flexible charging solutions for various electric vehicles. This device operates on a 3-phase + Neutral, 32A electrical supply, delivering power from 4 kW to 22 kW.
1.2. Safety Instructions
- Installation must be performed by a qualified electrician in accordance with local and national electrical codes.
- Do not attempt to open or repair the charging station yourself. Contact qualified service personnel.
- Ensure the charging station is properly grounded.
- Do not use the charging station if it is damaged or shows signs of malfunction.
- Keep children and unauthorized persons away from the charging station during operation.
- Avoid exposing the charging station to extreme temperatures, direct sunlight for prolonged periods, or corrosive substances.
2. Product Description
2.1. Features
- Compatible with Mode 3 (Type 3) and Mode 2 charging.
- Free access operation.
- Power output: 4 kW to 22 kW.
- Input: 3-phase + Neutral, 32A.
- Integrated status indicator light.
2.2. Components
The Hager WITTY charging station typically includes:
- Charging station unit
- Mounting hardware (screws, anchors)
- User manual (this document)
Figure 1: Front view of the Hager WITTY charging station with a green operational light, mounted on a textured wall.
Figure 2: Side view of the Hager WITTY charging station, illustrating the cable connection point and the unit's profile.
Figure 3: Detailed front view of the Hager WITTY charging station, emphasizing the integrated green status light.
3. Setup
3.1. Installation Location
Choose a suitable location that is protected from direct impact, excessive moisture, and extreme temperatures. Ensure adequate ventilation and accessibility for maintenance.
3.2. Mounting
- Mark the drilling points on the wall using the provided template (if applicable) or by measuring the mounting holes on the unit.
- Drill holes and insert appropriate wall anchors.
- Secure the charging station to the wall using the provided screws.
3.3. Electrical Connection
WARNING: Electrical installation must be performed by a qualified electrician.
- Ensure the main power supply is disconnected before beginning any electrical work.
- Connect the 3-phase + Neutral (3Ph+N) 32A power supply to the designated terminals inside the charging station.
- Ensure proper grounding is established.
- Verify all connections are secure and correctly wired according to the wiring diagram provided with the unit (refer to the separate installation guide for detailed diagrams).
- Close the charging station cover securely.
4. Operating
4.1. Starting a Charge
- Ensure the charging station is powered on and the status indicator light is green (ready).
- Connect the charging cable to your electric vehicle's charging port.
- Connect the other end of the charging cable to the charging station's outlet (Type 3 or Mode 2 socket).
- The charging station will automatically initiate the charging process. The status indicator light may change to blue or flashing green, depending on the charging status.
4.2. Stopping a Charge
- Disconnect the charging cable from your electric vehicle first.
- Disconnect the charging cable from the charging station.
- The charging station will return to a ready state (green indicator light).
4.3. Status Indicators
- Green Light: Ready for charging.
- Blue Light (or flashing green): Charging in progress.
- Red Light (or flashing red): Error or fault detected. Refer to the Troubleshooting section.
- No Light: Power off or system fault.
5. Maintenance
5.1. Cleaning
Clean the exterior of the charging station with a soft, damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals. Ensure the unit is powered off before cleaning.
5.2. Inspection
Periodically inspect the charging station for any signs of damage, wear, or loose connections. Check the charging cable for fraying or damage. If any damage is found, discontinue use and contact a qualified technician.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power/No light | Power supply disconnected; Circuit breaker tripped. | Check power supply; Reset circuit breaker. If problem persists, contact a qualified electrician. |
| Red indicator light | Internal fault; Overcurrent; Ground fault. | Disconnect and reconnect the vehicle. If the error persists, power cycle the unit. If still red, contact service. |
| Charging not starting | Cable not properly connected; Vehicle not ready to charge; Charging station fault. | Ensure cable is securely connected to both vehicle and station. Check vehicle's charging status. Power cycle the charging station. |
7. Specifications
| Feature | Detail |
|---|---|
| Model | XEV103 |
| Charging Mode | Mode 3 (IEC 61851-1), Mode 2 |
| Connector Type | Type 3 / Standard Socket |
| Input Voltage | 3-phase + Neutral |
| Max Current | 32A |
| Power Output | 4 kW to 22 kW |
| Access | Free Access |
| ASIN | B00CSJUVKA |
8. Warranty and Support
For warranty information and technical support, please refer to the official Hager website or contact your local Hager distributor. Keep your purchase receipt for warranty claims.
Spare parts availability: Information not available.
