1. Introduction
This manual provides essential instructions for the safe and efficient use of your Claber Aquauno Programmer, model 53921 8425. This device is designed to automate garden watering by connecting directly to a tap, offering a simple and reliable solution for irrigation management.
Image 1: Front view of the Claber Aquauno Programmer, showing the green START button, red STOP button, and the battery compartment cover.
2. Safety Information
Please read and understand all safety warnings before operating the device. Failure to follow these instructions may result in damage to the product or personal injury.
- Avoid Freezing Temperatures: Do not expose the programmer to temperatures below freezing. Remove the device from the tap and store it indoors during winter months to prevent damage.
- Not Suitable for Children: Keep the device out of reach of children.
- Outdoor Use Only: This programmer is designed exclusively for outdoor use.
- Do Not Immerse in Water: The device is water-resistant but not submersible. Do not put it under water.
- Installation Location: Do not install the programmer inside valve boxes or other enclosed spaces. It must be installed outdoors.
Image 2: Excerpt from the instruction sheet illustrating safety warnings and proper installation guidelines.
3. Package Contents
The Claber Aquauno Programmer package typically includes:
- 1 x Claber Aquauno Programmer (Model 53921 8425)
- 1 x Instruction Manual (this document)
Note: A 9V alkaline battery is required for operation and is not included.
4. Installation
4.1. Battery Installation
- Open the battery compartment cover located at the bottom front of the programmer.
- Insert a new 9V alkaline battery, ensuring correct polarity.
- Close the battery compartment cover securely.
Image 3: Diagram from the instruction sheet illustrating the correct insertion of a 9V battery into the programmer's compartment.
4.2. Attaching to the Tap
- Ensure the tap is clean and free of debris.
- Screw the programmer directly onto a standard 3/4" outdoor tap. Hand-tighten only; do not overtighten.
- Connect your garden hose or irrigation system to the outlet of the programmer.
- Open the tap fully. The programmer is designed to operate under normal tap pressure.
Image 4: The programmer securely attached to an outdoor tap, with an irrigation hose connected to its outlet.
5. Setup and Operating Instructions
The Claber Aquauno Programmer features a simple, one-program setup for daily automatic watering.
5.1. Programming the Watering Duration
- Ensure the tap is open.
- Press the green START button to begin watering. Water will start flowing.
- Allow the water to flow for the desired duration (minimum 1 minute, maximum 60 minutes).
- Once the desired watering time has passed, press the red STOP button. The water flow will cease.
- The programmer has now memorized this watering duration. It will automatically repeat this cycle once every 24 hours at the same time you pressed the green START button.
5.2. Manual Operation / Resetting the Program
- To manually start watering outside of the programmed cycle, simply press the green START button. Water will flow until you press the red STOP button. This manual operation does not affect the stored daily program.
- To reset the stored program and set a new watering duration, repeat the steps in section 5.1. The new duration will overwrite the previous one.
6. Maintenance
6.1. Battery Replacement
The programmer is powered by a 9V alkaline battery. When the battery level is low (approximately 8V), the device will automatically switch to a 48-hour watering cycle to conserve energy. Replace the battery as soon as possible to ensure continuous operation. Refer to section 4.1 for battery installation instructions.
6.2. Winter Storage
Before the first frost, remove the programmer from the tap. Drain any remaining water and store the device in a dry, frost-free location indoors. Prolonged exposure to direct sunlight and extreme temperature fluctuations (especially freezing) can reduce the product's lifespan.
Image 5: Excerpt from the instruction sheet detailing battery replacement and recommendations for winter storage.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No water flow when START button is pressed. |
|
|
| Watering cycle occurs every 48 hours instead of 24 hours. | Battery is low. | Replace the 9V alkaline battery immediately. |
| Incorrect watering duration. | Programmed duration was set incorrectly. | Repeat the programming steps (section 5.1) to set the desired duration. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | 53921 (8425) |
| Brand | Claber |
| Power Source | 1 x 9V Alkaline Battery (not included) |
| Watering Duration | 1 to 60 minutes |
| Watering Frequency | Every 24 hours (or 48 hours if battery is low) |
| Inlet Connection | 3/4" Tap Thread |
| Material | Plastic |
| Item Weight | 371 Grams (approx. 13.1 ounces) |
| Product Dimensions | Approx. 4.4 inches (11 cm) width. (Note: The provided product dimensions of 47.24"D x 70.87"W x 31.5"H appear to be incorrect for a tap timer. Please refer to the visual dimension guide or actual product for precise measurements.) |
| UPC | 800062528425 |
Image 6: Visual representation of the programmer's dimensions, indicating a width of approximately 4.4 inches (11 cm).
9. Warranty Information
For detailed warranty information, please refer to the documentation included with your purchase or visit the official Claber website. Warranty terms and conditions may vary by region and retailer.
10. Support
For further assistance, product registration, or to download the latest version of this manual, please visit the official Claber website:
