RAB Lighting LFP38A Landscape Flood Light Fixture User Manual

1. Introduction

This manual provides detailed instructions for the safe installation, operation, and maintenance of the RAB Lighting LFP38A Landscape Flood Light Fixture. Please read this manual thoroughly before installation and retain it for future reference.

The RAB Lighting LFP38A is a durable outdoor flood light fixture designed for landscape illumination. It accommodates a 150-watt maximum PAR38 bulb and operates on a 120-volt electrical system.

2. Safety Information

WARNING: Risk of electric shock. Disconnect power before installation or servicing.

• Ensure the power supply is turned off at the circuit breaker before beginning any work.
• All wiring must be in accordance with national and local electrical codes. If you are unsure about wiring, consult a qualified electrician.
• Do not exceed the maximum wattage specified for the bulb (150-watt PAR38).
• This fixture is designed for outdoor use and is water-resistant. However, ensure all connections are properly sealed to prevent water intrusion.
• Do not operate the fixture with a damaged cord or if the housing is compromised.
• Allow the bulb to cool completely before attempting to replace it.

3. Package Contents

Verify that all components are present before proceeding with installation:

• RAB Lighting LFP38A Flood Light Fixture (1 unit)
• Mounting hardware (if applicable, typically included with the fixture)
• Instruction Manual (this document)

Note: Bulb is not typically included and must be purchased separately.

4. Setup and Installation

Follow these steps for proper installation of your RAB Lighting LFP38A fixture:

4.1 Tools Required

• Screwdriver
• Wire strippers
• Pliers
• Electrical tape (optional, for added insulation)
• Weatherproof sealant (optional, for outdoor connections)

4.2 Mounting the Fixture

The LFP38A fixture features a 1/2 Inch NPS Threaded Locking Swivel Arm for versatile mounting. This allows for precise aiming of the light.

Image: Detail of the 1/2 inch NPS threaded locking swivel arm, indicating its adjustability and connection point.

1. Turn off power: Locate the circuit breaker controlling the outdoor lighting circuit and switch it to the OFF position. Verify power is off using a voltage tester.
2. Prepare mounting surface: Ensure the mounting surface is stable and can support the fixture.
3. Attach mounting arm: Secure the 1/2 inch NPS threaded swivel arm to a junction box or appropriate mounting accessory. Ensure a watertight seal for outdoor applications.
4. Wire connections: Connect the fixture's wires to the main power supply wires. Typically, this involves connecting black to black (live), white to white (neutral), and green/bare copper to green/bare copper (ground). Use approved wire connectors.
5. Secure connections: Ensure all wire connections are tight and properly insulated. For outdoor use, consider using weatherproof wire nuts and sealing the junction box.
6. Install bulb: Carefully screw a PAR38 or PAR20 bulb (up to 150 watts) into the fixture's socket. Do not overtighten.

Image: The RAB Lighting LFP38A fixture, ready for installation.

Image: The flood light fixture installed and illuminating an area, highlighting its ease of installation.

5. Operating Instructions

Once the RAB Lighting LFP38A fixture is securely installed and wired:

1. Restore Power: Turn the circuit breaker back to the ON position.
2. Test Operation: The light should illuminate.
3. Adjust Aim: Loosen the locking swivel arm, adjust the fixture to the desired angle for optimal illumination, and then tighten the swivel arm to secure its position. The fixture allows for 180-degree adjustment.

Image: An illustration demonstrating the 180-degree rotational capability of the fixture's mounting arm for precise light direction.

6. Maintenance

Regular maintenance ensures optimal performance and longevity of your flood light fixture.

• Cleaning: Periodically clean the fixture with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure power is off before cleaning.
• Bulb Replacement:
  1. Turn off power at the circuit breaker.
  2. Allow the old bulb to cool completely.
  3. Carefully unscrew the old bulb.
  4. Screw in a new PAR38 or PAR20 bulb (max 150 watts) into the socket.
  5. Restore power and test.
• Inspection: Annually inspect the wiring and housing for any signs of wear, damage, or corrosion. Address any issues promptly.

Image: The fixture is designed to withstand various outdoor weather conditions, including sun, rain, and snow.

7. Troubleshooting

If your RAB Lighting LFP38A fixture is not functioning as expected, consider the following common issues:

If troubleshooting steps do not resolve the issue, contact RAB Lighting customer support.

8. Specifications

9. Warranty Information

This RAB Lighting LFP38A fixture is covered by a 1-year manufacturer's warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from improper installation, accident, misuse, abuse, or unauthorized modifications.

For warranty claims or further details, please contact RAB Lighting customer support.

10. Customer Support

For technical assistance, replacement parts, or warranty inquiries, please contact RAB Lighting directly.

Visit the official RAB Lighting website for contact information and additional resources: www.rablighting.com