1. Introduction
This manual provides essential information for the safe and efficient operation, setup, and maintenance of your Antari ANF350 Fog Machine. Please read this manual thoroughly before operating the device to ensure proper function and to prevent damage or injury.
The Antari ANF350 is a water-based effect machine designed to produce a light, hazy smoke, ideal for enhancing lighting effects in various environments. It features an advanced pumping and fan system for efficient fluid consumption and includes built-in DMX control capabilities.
2. Safety Information
WARNING: Failure to follow these safety instructions may result in fire, electric shock, injury, or damage to the product or property.
- Always disconnect the power cord before cleaning, servicing, or when the machine is not in use.
- This machine is designed for indoor use only. Do not expose to rain or moisture.
- Use only Antari-approved water-based fog fluid. Using other types of fluid may cause damage to the machine and void the warranty.
- Do not operate the machine without fluid. Ensure the fluid reservoir is adequately filled.
- Keep the machine upright during operation. The spill-proof reservoir helps prevent leaks, but proper orientation is recommended.
- Ensure adequate ventilation around the machine. Do not block air vents.
- Keep out of reach of children.
- Do not point the output nozzle directly at people or animals.
- If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
3. Product Features
- Lightweight and compact design.
- Advanced pumping and fan system for efficient fluid consumption (up to 60 hours per gallon).
- Uses non-residue, water-based fluid, preventing damage to floors or carpets.
- Built-in DMX control for integration into lighting systems.
- Manual control options directly on the unit.
- Spill-proof fluid reservoir for secure operation in various orientations.
- Automatic heating and self-cleaning functions when DMX signal is detected/lost.
4. Components and Controls
Familiarize yourself with the main components of your ANF350 Fog Machine.
Figure 1: Front and side view of the Antari ANF350 Fog Machine, showing the output nozzle and fan grille.
Figure 2: Rear panel of the Antari ANF350 Fog Machine, displaying the fluid reservoir, DMX input/output, remote control port, power switch, power input, fuse, and control knobs for smoke and fan output.
Rear Panel Controls:
- Fluid Reservoir: Transparent tank for fog fluid.
- DMX IN/OUT: XLR connectors for DMX signal.
- DIP Switches: For setting DMX address.
- Remote Control Port: For optional wired remote.
- Smoke Knob: Adjusts fog output intensity.
- Fan Knob: Adjusts fan speed.
- Status Indicator: LED to show machine status (e.g., heating, ready).
- Power Switch: Main power toggle.
- Power Input: IEC power connector.
- Fuse Holder: Contains the main fuse for electrical protection.
5. Setup
5.1 Unpacking
Carefully remove the ANF350 from its packaging. Inspect the unit for any signs of damage during transit. Retain the packaging for future storage or transport.
5.2 Fluid Installation
- Ensure the machine is powered off and unplugged.
- Locate the fluid reservoir cap on the top of the unit.
- Unscrew the cap and carefully pour Antari-approved water-based fog fluid into the reservoir. Do not overfill.
- Securely replace the cap.
5.3 Placement
Place the ANF350 on a stable, level surface. Ensure there is adequate space around the machine for ventilation and that the output nozzle is directed away from people, animals, and sensitive equipment. The unit can be operated in a standard upright position or laid flat using optional feet (if included).
5.4 Power Connection
Connect the provided power cord to the power input on the rear panel of the ANF350, then plug the other end into a grounded electrical outlet of the correct voltage.
5.5 DMX Setup (Optional)
If using DMX control, connect a DMX cable from your DMX controller to the DMX IN port on the ANF350. If daisy-chaining multiple DMX devices, connect from the DMX OUT of the ANF350 to the DMX IN of the next device. Set the DMX address using the DIP switches on the rear panel according to your DMX controller's instructions.
6. Operation
6.1 Powering On
After connecting power and fluid, flip the main power switch on the rear panel to the 'ON' position. The machine will begin its warm-up cycle. The status indicator will typically illuminate to show heating progress. Once ready, the indicator will change (e.g., turn solid green).
6.2 Manual Control
Once the machine is ready, use the 'Smoke' knob to adjust the fog output intensity and the 'Fan' knob to control the fan speed, which affects the dispersion of the fog.
6.3 DMX Control
When a DMX signal is received, the ANF350 automatically turns on and begins heating. You can then control the fog output and fan speed via your DMX controller, using the assigned DMX channels. Refer to your DMX controller's manual and the ANF350's DMX chart (usually found in a separate DMX supplement or on the unit itself) for specific channel assignments.
Figure 3: The Antari ANF350 Fog Machine in operation, demonstrating the emission of a fine haze.
6.4 Powering Off
To power off the machine, simply flip the main power switch to the 'OFF' position. If operating under DMX control, the machine will initiate a self-cleaning process and then enter a 'sleep' mode when the DMX signal is removed.
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your ANF350 Fog Machine.
7.1 Cleaning
- Exterior: Wipe the exterior of the machine with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Internal System: The ANF350 features an automatic self-cleaning process when the DMX signal is removed. For extended periods of non-use (more than 30 days), it is recommended to run a cleaning cycle using Antari-approved cleaning fluid or distilled water. Operate the machine with cleaning fluid for a few minutes, then empty the reservoir and store.
7.2 Fluid Replacement
Always ensure sufficient fluid is in the reservoir before operation. If the fluid level is low, refill it following the instructions in Section 5.2. Do not mix different types of fog fluid.
7.3 Storage
When storing the machine for an extended period, ensure the fluid reservoir is empty or contains cleaning fluid after a cleaning cycle. Store the unit in a dry, dust-free environment.
8. Troubleshooting
If you encounter issues with your ANF350, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No fog output | No fluid in reservoir; Machine not warmed up; Clogged nozzle/pump; Power issue. | Check fluid level; Wait for warm-up; Perform cleaning cycle; Check power connection and fuse. |
| Weak fog output | Low fluid level; Incorrect fluid type; Partially clogged nozzle; Low 'Smoke' knob setting. | Refill fluid; Use Antari-approved fluid; Perform cleaning cycle; Increase 'Smoke' knob setting. |
| Machine not powering on | No power; Blown fuse; Faulty power switch. | Check power outlet and cable; Replace fuse (refer to fuse specifications); Contact service if switch is faulty. |
| DMX control not working | Incorrect DMX address; Faulty DMX cable; DMX controller issue. | Verify DMX address settings; Test DMX cable; Check DMX controller functionality. |
If problems persist after attempting these solutions, please contact Antari customer support or a qualified service technician.
9. Specifications
| Feature | Detail |
|---|---|
| Model | ANF350 |
| Item Weight | 23 pounds (approx. 10.4 kg) |
| Product Dimensions | 16 x 10 x 18 inches (approx. 40.6 x 25.4 x 45.7 cm) |
| Fluid Type | Water-based fog fluid (Antari-approved) |
| Fluid Consumption | Up to 60 hours per gallon (approx. 3.78 liters) |
| Control | Manual knobs, Built-in DMX |
| Hardware Platform | CONSUMER_ELECTRONICS |
10. Warranty and Support
Warranty information for the Antari ANF350 Fog Machine is not provided within this manual. For details regarding warranty coverage, terms, and conditions, please refer to the documentation included with your purchase or contact Antari customer support directly. You may also visit the official Antari website for the most current support information.
For technical assistance, spare parts, or service inquiries, please contact your authorized Antari dealer or the manufacturer's customer service department.
