Introduction
The OMRON RS2 Electronic Wrist Blood Pressure Monitor is a compact and easy-to-use device designed for accurate blood pressure measurement at home or on the go. It features irregular heartbeat detection and stores up to 30 measurements for tracking your health over time. This device is clinically validated to ensure reliable results.
Image: The OMRON RS2 Wrist Blood Pressure Monitor, showing its compact design and digital display with blood pressure readings.
Setup
1. Battery Installation
The OMRON RS2 requires two AAA alkaline batteries (included). To install:
- Open the battery compartment cover on the back of the monitor.
- Insert the two AAA batteries according to the polarity markings (+/-) inside the compartment.
- Close the battery compartment cover securely.
2. Applying the Wrist Cuff
Proper cuff placement is crucial for accurate readings. Ensure the monitor is positioned correctly on your wrist.
- Remove any tight-fitting clothing from your left wrist.
- Place the monitor on your left wrist with the display facing upwards. The bottom edge of the cuff should be approximately 1 to 2 cm from the palm of your hand.
- Wrap the cuff snugly around your wrist, ensuring it is not too tight or too loose. The cuff should feel firm but comfortable.
Image: A person demonstrating the correct way to wrap the wrist cuff around their left wrist, ensuring a snug fit.
Image: The OMRON RS2 monitor correctly positioned on a wrist, with the display facing up and the cuff properly secured.
Operating Instructions
Taking a Measurement
For accurate readings, follow these steps:
- Sit quietly for at least 5 minutes before taking a measurement.
- Sit in a chair with your feet flat on the floor and your back supported.
- Place your elbow on a table so that the monitor is at the same level as your heart.
- Press the START/STOP button. The cuff will begin to inflate automatically.
- Remain still and do not talk during the measurement.
- Once the measurement is complete, your blood pressure (systolic and diastolic) and pulse rate will be displayed.
Understanding Your Readings
- SYS (Systolic Pressure): The top number, indicating the pressure in your arteries when your heart beats.
- DIA (Diastolic Pressure): The bottom number, indicating the pressure in your arteries between beats.
- PULSE: Your heart rate, measured in beats per minute.
- Irregular Heartbeat Detection: If an irregular heartbeat is detected during the measurement, a symbol will appear on the display. Consult your doctor if this symbol appears frequently.
- Hypertension Indicator: If your systolic pressure is 135 mmHg or higher, or your diastolic pressure is 85 mmHg or higher, the heartbeat symbol will blink, indicating potential hypertension.
- Correct Cuff Wrapping Indicator: An "OK" symbol indicates that the cuff has been wrapped correctly, ensuring accurate measurement.
Image: Close-up of the OMRON RS2 monitor's display, showing typical readings for systolic, diastolic, and pulse, along with the "OK" indicator for correct cuff placement.
Memory Function
The OMRON RS2 automatically stores up to 30 measurements. To view past readings, press the Memory button (represented by a notebook icon on the device). Pressing it repeatedly will cycle through the stored measurements from most recent to oldest.
Maintenance
Cleaning
Wipe the monitor and cuff with a soft, dry cloth. If necessary, use a cloth dampened with water and a mild soap, then wipe dry. Do not use abrasive cleaners or immerse the unit in water.
Storage
Store the monitor in its protective case (if included) in a clean, dry place. Avoid extreme temperatures, humidity, direct sunlight, and dust.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No display when pressing START/STOP. | Batteries are dead or incorrectly inserted. | Replace batteries with new AAA alkaline batteries, ensuring correct polarity. |
| Error message (e.g., "E1", "E2") displayed. | Cuff not wrapped correctly, movement during measurement, or irregular pulse. | Re-wrap the cuff snugly, remain still and silent during measurement. If errors persist, consult the full manual or contact support. |
| Readings seem too high or too low. | Incorrect posture, cuff placement, or recent activity. | Ensure proper sitting posture, cuff at heart level, and relax for 5 minutes before measuring. Avoid caffeine, exercise, or smoking before measurement. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | HEM-6113-E |
| Measurement Method | Oscillometric method |
| Measurement Range | Pressure: 0 to 299 mmHg, Pulse: 40 to 180 beats/min. |
| Accuracy | Pressure: ±3 mmHg, Pulse: ±5% of display reading |
| Power Source | 2 x 1.5V (LR03, AAA alkaline batteries) |
| Battery Life | Approximately 300 measurements with new alkaline batteries at 23°C |
| Console Weight | Approximately 101g without batteries |
| Measurable Wrist Circumference | Approximately 13.5 to 21.5 cm |
| Dimensions (L x W x H) | 2.11 x 7.8 x 5.99 cm |
| Memory | 30 measurements |
Image: Product packaging showing detailed specifications for the OMRON Wrist Blood Pressure Monitor, model HEM-6121 (similar to RS2).
Warranty and Support
OMRON Healthcare products are manufactured under strict quality control. For warranty information and customer support, please refer to the warranty card included with your product or visit the official OMRON Healthcare website. You can also contact their customer service for assistance with your OMRON RS2 monitor.
For more information, visit the Omron Brand Store.
