1. Product Overview
The APC Smart-UPS X SMX120RMBP2U is a high-quality external battery backup unit designed to provide clean and reliable network-grade power, protecting critical data and equipment from power problems. This unit offers extended run options, making it ideal for servers, storage, and networks with varying load consumption. It features legendary reliability, manageability, and high efficiency across low, medium, and high load levels.
Figure 1: APC Smart-UPS X SMX120RMBP2U External Battery Backup Unit
2. Safety Information
Always read and understand all instructions before installing or operating this unit. Failure to do so may result in injury or equipment damage. This unit contains sealed lead-acid batteries. Do not open or mutilate batteries. Released electrolyte is harmful to skin and eyes. It may be toxic. Always ensure the unit is unplugged from the main power source before performing any maintenance or battery replacement. Refer to local regulations for proper disposal of batteries.
3. Package Contents
Verify that all components are present upon unpacking:
- APC Smart-UPS X SMX120RMBP2U External Battery Backup Unit
- User Manual (this document)
- Necessary connection cables
4. Setup
4.1 Initial Battery Connection
Upon receiving your UPS, the internal battery may be disconnected for safety during shipping. You will need to connect the battery before initial use. Refer to the instructions below for proper connection.
Video 1: Overview of APC UPS for SmartHome Devices. This video demonstrates the general concept of UPS usage for home devices, including initial setup considerations.
4.2 Connecting to Power and Devices
- Plug the UPS power cord directly into a properly grounded wall outlet. Avoid using extension cords.
- Connect your critical equipment (servers, network devices) to the battery backup outlets (typically labeled). These outlets provide power during outages.
- Connect non-critical equipment to the surge-only outlets. These outlets provide surge protection but no battery backup.
- For automatic computer shutdown during extended power outages, connect the provided data cable from the UPS data port to your computer. Install the APC PowerChute software (available from the manufacturer's website) on your computer.
5. Operation
5.1 Turning On/Off
- To turn on the UPS: Press and hold the power button until the display illuminates.
- To turn off the UPS: Press and hold the power button until the display turns off.
5.2 Display Information
The front panel display provides real-time information about the UPS status:
- On Line: Indicates the UPS is receiving utility power.
- Load: Shows the percentage of connected load.
- Battery Charge: Displays the current battery charge level.
- Estimated Run Time: Provides an estimate of how long the UPS can power connected devices during an outage.
- Input/Output Voltage: Shows the current input and output voltage.
6. Maintenance
6.1 Battery Replacement
The internal batteries are maintenance-free, sealed lead-acid. They are hot-swappable, meaning they can be replaced without shutting down connected equipment. However, for safety, it is recommended to disconnect the UPS from the main power source before replacement.
- Ensure the UPS is disconnected from the wall outlet.
- Locate the battery access panel, typically on the side or front of the unit.
- Remove any retaining screws or latches securing the panel.
- Carefully slide out the old battery pack. Note the orientation and connection points.
- Disconnect the battery cables (red and black) from the old battery.
- Connect the new battery cables to the new battery, ensuring correct polarity (red to red, black to black).
- Slide the new battery pack into the unit, ensuring it is securely seated.
- Replace the access panel and any retaining screws/latches.
- Reconnect the UPS to the wall outlet.
7. Troubleshooting
7.1 UPS Beeping Continuously
- Cause: The battery may be disconnected or improperly installed.
- Solution: Ensure the battery is correctly connected and seated. For new units, the battery might be shipped upside down or disconnected. Follow the battery installation steps in Section 6.1.
7.2 No Power Output
- Cause: UPS is off, battery is depleted, or circuit breaker tripped.
- Solution: Turn on the UPS. Check the battery charge level. Reset the circuit breaker on the back of the unit if it has tripped.
7.3 Short Run Time
- Cause: Overload, aging battery, or insufficient charge.
- Solution: Reduce the connected load. Allow the battery to fully charge (up to 3 hours). If the battery is old, consider replacing it.
8. Specifications
| Feature | Specification |
|---|---|
| Product Dimensions | 33 x 24 x 10 inches |
| Item Weight | 140 pounds |
| Manufacturer | SCHNEIDER ELECTRIC IT - CONTAINER |
| Item Model Number | SMX120RMBP2U |
| Batteries Required | 1 Product Specific batteries required. |
| Battery Cell Composition | Lead Acid |
| Voltage | 120 Volts |
| Color | Black |
| Material | Metal |
| Load Capacity (VA) | 1000 VA |
| Load Capacity (Watt) | 800 W |
| Rack Height | 2U |
| Receptacles | 8 x NEMA 5-15R |
| Hot Swappable Batteries | Yes |
| Maximum Battery Recharge Time | 3 Hour |
9. Warranty and Support
For warranty information and customer support, please refer to the official Schneider Electric website or contact their customer service directly. You can also find additional support resources through the provided customer support link.
